NEO NXB - 12020A Voltage / Current Breakout Test Box
- On-Off power switch
- 20 A Circuit Breaker
- 8’ Flexible Power Cord
- Outlets – (4) 5-20R
- 3ft.
- (2) fork terminals (current)
- (1) fork terminals (ground)
- (2) Shielded Banana (voltage)
Multiple outlets provide flexibility in connecting equipment under test. Tester pigtail interface simplifies connecting to a variety of voltage/current measuring systems.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
120/240 | 20A | AC Line - Cord | 5-20 R [4] | Pigtail | Yes |
More Product Information
Beginning in 2019, AR will be embedding ampwebwARe in all new amplifiers. Once an amplifier is connected to a network and an IP address is set, any other device connected to that network can access the amplifier’s embedded webpage. The features of this embedded webpage include:
- All Information Shown on One Screen
- Simple User Interface
- Allows for Remote Diagnostics
- Monitor Status from Anywhere
- Multiple Simultaneous Browser Connections
- Many Supported Web Browsers
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
We subject our amplifiers to the harshest conditions just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 W that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications.
These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers.
These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
-
High responsiveness following to the image can be realized because of the image recognition setting according to colors on the sensor part.
-
Composite strength distribution of the actual image taken by the camera and the measured data can be visualized.
- On-Off power switch
- 20 A Circuit Breaker
- 8’ Flexible Power Cord
- Outlets – (4) 5-20R
- 3ft.
- (2) fork terminals (current)
- (1) fork terminals (ground)
- (2) Shielded Banana (voltage)
-
NEO 941 parts are AS5836 compatible (Clam Shell Clamps not Included)
-
NEO 942 parts are AS1653 compatible (Clam Shell Clamps not Included)
-
NEO 941 parts are AS5836 compatible (Clam Shell Clamps not Included)
-
NEO 942 parts are AS1653 compatible (Clam Shell Clamps not Included)
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.