NEO NXB - 20820S Voltage / Current Breakout Test Cable
-
15’ Flexible Power Cord
-
IEC C13 / C14 Connectors
Test Tap:
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
Simple single input output (IEC C13/C14) connection with pigtail tap for connecting to power meter.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
208 | 20A | C14 | C13 | Pigtail | No |
Application
More Product Information
The system detects position of the magnetic field sensor on the basis of the image on the camera first of all and then, recognizes strength of the signal that is measured by the sensor upon frequency analysis of the signal almost simultaneously. Finally, visualization of the strength level in composition with the real image of the measured object can be realized on screen of PC in form of heat map in colors.
-
High responsiveness following to the image can be realized because of the image recognition setting according to colors on the sensor part.
-
Composite strength distribution of the actual image taken by the camera and the measured data can be visualized.
-
NEO 941 parts are AS5836 compatible (Clam Shell Clamps not Included)
-
NEO 942 parts are AS1653 compatible (Clam Shell Clamps not Included)
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
3KVA, 3KW Double Conversion On Line Isolated 115VAC Input UPS, and simultaneous 120 and 240VAC 60Hz Output, Power Factor Correction, Extended Internal Batteries, SNMP Communications for Military Applications
-
On-Off power switch
-
20 A Circuit Breaker
-
Inlet - NEMA L6-20
-
Outlets – NEMA L6-20R
Test Tap:
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
-
15’ Flexible Power Cord
-
IEC C13 / C14 Connectors
Test Tap:
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
-
GPS signals simulated: L1, L1C*, L2C*, L5*
-
Galileo signals simulated: E1, E5**, E5a**, E5b**
-
Simultaneous GPS/Galileo simulation
-
WAAS/EGNOS SBAS simulation
-
Static and dynamic simulations via NMEA-0183 File Record and Playback
-
12 channel configuration available with upgrade path (RAIM supported)
-
Programmable space vehicle (SV) parametrics and health
-
User or built-in GPS receiver referenced time and date
-
PVT data available via RS-232
-
User Defined Data Transferable between Linked GPSG units
-
Remote control interface Ethernet
* For tracking of L1C, L2C or L5 signals some receivers require synchronized L1 transmissions.
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
-
NEO 941 parts are AS5836 compatible (Clam Shell Clamps not Included)
-
NEO 942 parts are AS1653 compatible (Clam Shell Clamps not Included)
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.
Test & Measurement
Download Line Card
Document