Products

Displaying 1 - 12 of 12

Abaco PMC-422 Serial Controller - 8-port PMC for VME, CompactPCI

  • 4 RS232 ports can be accessible via front RJ45 connectors
  • All ports accessible on rear I/O J4 with PMC I/O Module (PIM) PIM422
  • 8 high-performance 16C550 UARTs with 64 bytes of RX/RX FIFO per channel
  • PMC form factor
  • PCI bus 2.2 target interface compliant up to 33MHz clock, 32-bit bus
  • 8 port RS232/RS422/RS485 serial controller

Abaco PMC-422/FP - Mezzanine Card Serial I/O for VME, CompactPCI

  • Read/write burst operation
  • Data transfer in byte, word, and double-word
  • Four ports routed to the front utilizing RJ-45 connectors or eight ports routed to the front utilizing a 68-pin SCSI cable (06-260000x).
  • PMC/PCI form factor
  • Eight general purpose Inputs

Abaco PMC-HS-SERIAL (11050-201) PMC with 4 channels of high speed serial

  • Four channels of high-speed serial
  • Maximum data rate of 10 Mb/s (synchronious) and 2 Mb/s (asynchronous)
  • Asynchronous, monosync, bisync, HDLC, SDLC, LAPB, LAPD, ISDN, and PPP communication protocols supported
  • RS-232, RS-422, EIA-449, EIA-530, or V35 physical interferences supported
  • 306 x 32-bit total FIFO
  • PMC with front- and rear-panel I/O
  • PCIbus master
  • RoHS compliant

Abaco PMC-OCTPRO-232 Mezzanine Card - Expands eight RS-232 channels

  • PMC with eight RS-232 asynchronous serial channels
  • Data rates to 115.2 kbaud
  • I/O via front- or back-panel P4 connectors
  • 128-byte FIFOs for receive and transmit on each channel
  • Linux, VxWorks and Windows NT drivers available

Abaco PMC-OCTPRO-422 PCI Mezzanine Card - Expands eight RS-422 channels

  • PMC with eight RS-422 asynchronous serial channels
  • Data rates to 460.8 kbaud
  • I/O via front- or back-panel P4 connectors
  • 128-byte FIFOs for receive and transmit on each channel
  • Linux, VxWorks, and Windows NT drivers available

Abaco PMC423 Serial I/O Mezzanine 16-port serial, front and rear I/O

  • 16 Port Serial Controller with two 16-bit Timer/Counters
  • PMC/PCI Form Factor (66 MHz Capable)
  • 16 ports routed to the front and rear
  • Read/Write Burst Operation
  • Baud Rate from 150bps - 6.25Mbps
  • Software selectable RS232, RS422 & RS485
  • (Full Duplex & Half Duplex)
  • All Ports Fully Independent (16C550 Compatible Registers)

Abaco PowerPact3 IMP3A Rugged 3U CPCI QorIQ-based Single Board Computer

  • Freescale QorlQ processor up to 1.2 GHz
    • Two e500v2 cores
    • Shared 512 KB L2 Cache with ECC
    • Integrated DDR3 memory controller with ECC
  • Up to 4 GB DDR3 SDRAM with ECC 
  • Up to 2 GB NAND Flash and 128 KB of NVRAM
  • One PCI-X PMC expansion site
  • Rear I/O
    • 2x Gigabit Ethernet
    • 2x COM ports
    • 1x USB 2.0 ports
    • 2x SATA ports
    • Up to 6 4x PMC I/O
    • 16x GPIO
  • Operating system support for VxWorks®, and Linux
  • Single slot 3U CompactPCI form factor
  • Compliant to PCIMG® 2.0 R3.0

Abaco PowerXtreme PPC10A SBC - Rugged 6U VME single board computer with QorIQ Power Architecture

  • 6U VME Single Board Computer
  • P4080 processor
    • Eight e500mc cores @ up to 1.5 GHz
  • Dual-channel DDR3 (up to 8 GB)
  • 512 MB NOR Flash
  • 4 GB NAND Flash Solid-State Drive
  • 512 kB non-volatile MRAM
  • Host/Slave, VME64 Compliant + 2eSST support
  • 2x independent PMC/XMC Sites
  • AFIX SITE (SCSI/VGA/1553/Flash drive)
  • 2x 10/100/1000BaseT Ethernet +2x optional 10/100/1000BaseT Ethernet
  • 2x or 4x RS232 Debug
  • 4x RS232/422/485 sync/async
  • 2x Serial ATA (3Gb/s)
  • 2x USB 2.0 + 3x Optional USB 2.0 
  • Up to 31x Single-Ended GPIO (5V tolerant)
  • Front I/O (air-cooled variants only)
  • BMM Baseboard Management Controller

Abaco PowerXtreme PPC9B SBC - 6U VME single board computer w/ Power Architecture QorIQ P2020 processor

  • Freescale QorlQ P2020 processor up to 1.2 GHz
    • Two e500 cores
    • Shared 512 KB L2 Cache with ECC
    • Integrated DDR3 memory controller ECC 
  • Up to 2 GByte soldered DDR3 SDRAM with ECC
  • Up to 1 GByte Flash
  • 2x128 KB of NVRAM
  • Two on-board expansion sites One XMC/PMC and one PMC only
  • Front I/O (Air-cooled versions)
    • 1x Gigabit Ethernet
    • 1x USB 2.0
    • 1x UART port
  • Rear I/O (see datasheet for full specs)
  • Operating System Support for VxWorks, Open Source Linux
  • Single slot 6U VMEbus form factor

Abaco VME-6015 - Quad-Serial I/O Interface Board

  • Break generation and detection
  • Parity, overrun, and error detection
  • Even, odd, or no parity
  • 1, 1 1/2, or 2 stop bits
  • Asynchronous features
  • 5, 6, 7, or 8 bits/character
  • Double Eurocard form factor
  • Four programmable baud rate generators
  • Uses four industry-standard 25-pin subminiature D connectors
  • Modem control lines for each channel
  • Self-test capability
  • Programmable interrupt capability
  • 0 to 1 Mbaud data rate
  • RS-232C, RS-423, RS-422A, and RS-485 compatible
  • Fully programmable synchronous/asynchronous operation
  • Four full-duplex channels
  • A16:D8
  • Synchronous features

Acromag PMC520 Serial Communication, 232 Octal

  • 8 asynchronous EIA/TIA-232E serial ports
  • 64-byte FIFO buffers
  • Interrupt support
  • Programmable baud rate (up to 120Kbps)
These modules provide eight asynchronous serial communication ports from a single PMC Socket. Software-configuration helps you quickly set baud rates, character-sizes, stop bits, and parity. Signal support for RTS/CTS handshaking is also included.

Acromag PMC521 Serial Communication, 422/485 Octal

  • 8 asynchronous full duplex EIA/TIA-422B serial ports (supports EIA-485)
  • 64-byte FIFO buffers
  • Interrupt support
  • Programmable baud rate (up to 1.8432Mbps)