Products

Displaying 1 - 25 of 41

Acromag AcPC8625A - Nonintelligent 6U cPCI IP Carrier

  • Four IP module slots
  • Rear access I/O
  • Plug-and-play carrier configuration and interrupt support
The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus. All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards. And with Acromag’s 80mm transition module (TRANS-C200), all 200 I/O points are easily ported out the back of the cage.

Acromag AcPC8630A - Nonintelligent 3U cPCI IP Carrier, Front I/O

  • Two IP module slots
  • Front access I/O
  • Plug-and-play carrier configuration and interrupt support
The AcPC8630A is a nonintelligent slave board that interfaces two IP modules to the CompactPCI® (cPCI) bus. All 100 I/O points are brought out the front connectors for easy cable access.

Acromag AcPC8635A - Nonintelligent 3U cPCI IP Carrier, Rear I/O

  • Two IP module slots
  • Rear access I/O
  • Plug-and-play carrier configuration and interrupt support
The AcPC8635A is a non-intelligent slave board that interfaces two IP modules to the CompactPCI® (cPCI) bus. All 100 I/O points are brought out the rear J2 connector. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards.

Acromag APC8620A - Non-intelligent PCI Bus Carrier for IP Modules

  • Holds five IP modules
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system.
Five IP module slots give you the freedom to mix a variety of I/O functions (A/D, D/A, digital in, digital out, serial I/O, etc.) on a single board. Or, combine modules of the same type for hundreds of channels on a single card. Either way, the APC8620A saves your precious card slots and reduces your costs.
Select I/O modules from Acromag’s offering of more than forty models or use any third-party IP mezzanine ANSI/VITA 4 modules.
Specifications IP Module Compliance (ANSI/VITA 4): Meets or exceeds all written IP specifications per ANSI/VITA 4-1995 for 8MHz or 32MHz operation. Supports Type I and Type II ID space formats.

Acromag APC8621A - Non-intelligent PCI Bus Carrier, Half-Length

  • Nonintelligent PCI bus carrier
  • Holds three IP modules
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.

Acromag APCe8650 - Non-intelligent PCI Express Bus Carrier

  • Non-intelligent PCIe bus carrier
  • Holds four IP modules
This board interfaces standard Industry Pack (IP) mezzanine modules to a PCI Express bus on a PC-based computer system.
Four IP module slots give you the freedom to mix a variety of I/O functions (A/D, D/A, digital in, digital out, serial I/O, etc.) on a single board. Or, combine modules of the same type for hundreds of channels on a single card. Either way, the APCe8650 saves your precious card slots and reduces your costs.
Select I/O modules from Acromag’s offering of more than forty models or use any third-party ANSI/VITA 4 compliant IP modules.

Acromag AVME9630 - VMEbus 3U Carrier

  • NOT RECOMMENDED FOR NEW DESIGNS
  • Non-intelligent VME IP carrier
  • Holds two IP modules
  • Standard IP module interface
  • Supports two interrupt channels per IP

Acromag AVME9668 - VMEbus 6U Carrier

  • Non-intelligent VME IP carrier
  • Holds four IP modules
  • Front panel SCSI-2 connectors
  • Supports 8MHz and 32MHz IP clocks
  • Supports two interrupt channels per IP
The AVME9668 is a non-intelligent slave board that interfaces IP modules to the VMEbus. The full-height (6U) board holds four IP modules. All field I/O connections are made to the carrier board.

Acromag AVME9670 - VME64 Carriers

  • Non-intelligent VME64x IP carrier
  • Holds four IP modules
  • Rear Access I/O
  • Supports two interrupt channels per IP
The AVME9670 and AVME9675 are nonintelligent slave boards that interface up to four IP modules to the VMEbus. The only difference is that the AVME9675 adds fully implemented geographical addressing. Both are full-height (6U) IP carrier cards that use VME64-compliant connectors to increase the quantity of rear I/O connections beyond that of standard VME. Although the rear connectors are VME64, the electrical interface is standard VME A24/A16. This means that nearly all CPU products (VME64 or not) can still enjoy full access to the IP modules.

Acromag AVME9675 - VME64 Carriers with Geographical Addressing

  • Non-intelligent VME64x IP carrier
  • Holds four IP modules
  • Rear Access I/O
  • Supports two interrupt channels per IP
The AVME9670 and AVME9675 are nonintelligent slave boards that interface up to four IP modules to the VMEbus. The only difference is that the AVME9675 adds fully implemented geographical addressing. Both are full-height (6U) IP carrier cards that use VME64-compliant connectors to increase the quantity of rear I/O connections beyond that of standard VME. Although the rear connectors are VME64, the electrical interface is standard VME A24/A16. This means that nearly all CPU products (VME64 or not) can still enjoy full access to the IP modules.

Acromag Cables - Ribbon, SCSI, serial, and parallel communication signal cables:

Acromag provides a large selection of signal cables to complete the connection of the field wiring on the termination panel to the I/O board. We offer you a wide assortment of ribbon cables to accommodate the various pin and connector configurations. Cables range from simple 50-pin headers (shielded or unshielded) to high-speed SCSI cables. Cable support is available for all of Acromag’s analog I/O, digital I/O and serial communication boards.

Acromag IP-EP200: Cyclone II FPGA with Digital I/O (JTAG-configured)

  • Up to 48 TTL or 24 differential RS485
  • Altera Cyclone II EP2C20 FPGA programmable via JTAG port or via the IP bus directly
This series of plug-in mezzanine modules provides a user-customizable Altera® Cyclone II FPGA on an Industry Pack (IP) module. The module allows users to develop and store their own instruction set in the FPGA for adaptive computing applications. Typical uses include specialized communication systems over RS422/485 networks, test fixture simulation of signals over TTL-switched lines, and analysis of acquired data using specialized mathematical formulas such as those developed with MathWorks’s MatLab® software.

Acromag IP220A Analog Output Industry Pack Module, 12-bit D/A

  • 8 or 16 voltage output channels
  • Independent D/A converter on each channel
  • 11µS settling time
  • ±10V output range
The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
Each output channel has its own 12-bit D/A converter (DAC). Individual DACs are faster, and they eliminate glitches typically caused by the re-acquisition process of sample and holds found on multiplexed output boards.
Individual channels also have double-buffered data latches. You can select to update each output when it is written to, or to update all outputs simultaneously. Simultaneous outputs better simulate linear movements in motion processes.

Acromag IP230A Analog Output Module, 16-bit D/A

  • 4 or 8 voltage output channels
  • Individual D/A converters on each channel
  • 10µS settling time
  • Selectable output range (±5V, ±10V, 0-10V)
IP230A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs.

Acromag IP231 Analog Output Module, 16-bit D/A

  • 8 or 16 voltage output channels
  • Independent D/A converter on each channel
  • 13µS settling time
  • ±10V output range
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
Each output channel has its own 16-bit D/A converter (DAC). Individual DACs are faster, and they eliminate glitches typically caused by the re-acquisition process of sample and holds found on multiplexed output boards.

Acromag IP235A Analog Output Module, 16-bit D/A w/RAM Buffer

  • 8 voltage output channels
  • Individual D/A converters on each channel
  • 10µS settling time
  • Selectable output range (±5V, ±10V, 0-10V)
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.

Acromag IP236A Analog Output Module, 16-bit D/A w/FIFO Buffers

  • 8 voltage output channels
  • Individual D/A converters on each channel
  • 10µS settling time
  • Selectable output range (±5V, ±10V, 0-10V)
IP236A modules have 16-bit D/A converters (DAC) to provide highly-accurate analog voltage outputs. FIFO buffers enhance control over the transfer of data to the DAC and improve efficiency.

Acromag IP320A Analog Input Module, 12-bit A/D

  • 20 differential or 40 single-ended input channels
  • 200KHz throughput
  • 4.5µS/conversion
  • Selectable input range (±5V, ±10V, 0-10V)
The IP320A monitors 20 differential or 40 single-ended input channels. When used with a carrier that holds four IP modules, up to 160 inputs can be obtained from a single card cage slot.
A jumper offers a choice of three input voltage ranges. Using the software programmable gain, you can easily customize the input voltage on an individual channel basis. The control register provides further flexibility with the option of single-ended or differential inputs and controlled channel selection. Software or external triggers enable synchronization of data acquisition to external events.

Acromag IP330A - Analog Input Module, 16-bit A/D

  • 16 differential or 32 single-ended input channels
  • 200KHz throughput
  • 5µS/conversion
  • Selectable input range (±5V, ±10V, 0-5V, 0-10V)
IP330A Industrial I/O Pack (IP) modules provide fast, high-resolution A/D conversion.
The IP330A has many features to improve your overall system throughput rate. You can scan all channels or define a subset for more frequent sampling. Burst mode scans selected channels at the maximum conversion rate. Uniform mode performs conversions at user-defined intervals. Both modes can scan continuously, or execute a single cycle upon receiving a trigger.
“Mailbox” memory allows the CPU to read the latest data in 32 storage buffer registers without interrupting the A/D converter.

Acromag IP340 - Analog Input Module, Simultaneous Sample & Hold

  • 16 differential inputs (two 8-channel groups)
  • 12 or 14-bit A/D
  • 125KHz throughput
  • 8µS conversion time for 8-channel group
  • 512 sample FIFO buffer, ±10V input range

Acromag IP400 Digital Input Module, High Voltage Inputs

  • 40 input channels
  • 0-60V DC input range
  • Change-of-state/level interrupts (up to 12 channels)
The IP400 can monitor the on/off (high/low) status of up to 40 devices.
Loopback monitoring of critical control signals is easily accomplished with the IP400 by reading the output states of Acromag’s IP405 Output Module. The two modules share the same field interface pinouts for direct loopback compatibility.

Acromag IP405 Digital Output Module, High Voltage Outputs

  • 40 low-side switch output channels
  • 0-60V DC output range
  • High output current (up to 1A per channel)
The IP405 controls up to 40 low-side switches (open-drain MOSFETs).
Operation of this module is very simple. Writing a “0” bit to a channel data register opens the switch to turn off a field device. Similarly, writing a “1” bit closes the switch to turn on the device. Each register can be read back to verify the value. Loopback monitoring of critical control signals is easily accomplished by reading back output states using Acromag’s IP400 Digital Input Module.

Acromag IP408 Digital Input/Output Module, High Voltage I/O

  • 32 bi-directional digital input and/or output channels
  • 0-60V DC input and output range
  • Low-side output switches
  • Outputs sink up to 1A per channel
  • Change-of-state and level interrupts (up to 8 channels)

Acromag IP409 Digital Input/Output Module, Differential I/O

  • 24 differential digital input and/or output channels
  • Ruggedized RS-422A/485 transceivers
  • Interrupt support on all channels (change-of-state and high or low level transition
The IP409 provides 24 differential I/O channels with interrupts. Each channel is programmable as an input or an output on a bit basis, in any combination. All channels can generate change-of-state (COS), low, or high level transition interrupts.

Acromag IP440A Digital Input Module, Isolated

  • 32 port-isolated input channels
  • ±60V AC/DC input (three ranges)
  • Interrupt support for each channel
IP440A Industrial I/O Pack (IP) modules provide 32 optically isolated inputs to safely monitor a wide range of digital input voltage levels.
Isolation protects your computer system from noise, transient signals, and field wiring faults. The inputs are grouped into four 8-channel ports. Ports are isolated from the logic and each other.
Change-of-state interrupts are supported using paired channels. Debounce eliminates spurious interrupts from noise and switching transients for error-free edge detection.
Closed-loop monitoring of critical control signals is easily accomplished using the IP440A in conjunction with Acromag’s IP445 digital output module.

Pages