Abaco - PMC522/FP Eight Port Serial Controller I/O for VME and CompactPCI

Abaco - PMC522/FP Eight Port Serial Controller I/O for VME and CompactPCI
  • PMC form factor
  • Eight port RS-232/RS-422 serial controller
  • PCI bus 2.3 target interface compliant up to 33 MHz clock, 32-bit bus
  • Eight RS-232/RS-422 ports are accessible via front 68 pin high-density connector or on rear I/O via P14
  • Automatic RTS/CTS or DTR/ DSR flow control
  • Automatic Xon/Xoff software flow control
  • Conformal coating optional (Humiseal 1B31 or 1B73)

More

The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.

  • Eight general purpose RS232/RS-422 inputs
  • Read/write burst operation
  • Data transfer in byte, word, and double-word
  • Eight ports routed to the front utilizing a 68-pin high-density connector or eight ports routed to the rear via P14
  • PMC/PCI form factor

More Product Information

Abaco - PMC522 Four Port Serial Controller I/O for VME and CompactPCI
  • PMC form factor
  • Four port RS-232 serial controller
  • PCI bus 2.3 target interface compliant up to 33 MHz clock, 32-bit bus
  • Four high performance 16C550 UARTs with 64 bytes of TX/RX FIFO per channel
  • Four RS-232 ports are accessible on front via RJ45 connectors or rear I/O via P14
  • Automatic RTS/CTS or DTR/ DSR flow control
  • Automatic Xon/Xoff software flow control
  • Conformal coating optional (Humiseal 1B31 or 1B73)

Abaco - TRRM940 8-port transition module for 6U VME NETernity 24-port GbE PICMG 2.16
  • 8 10/100BaseTX ports with RJ45 connectors
  • Transition module for RM940 Ethernet switches
  • Ethernet/LAN Resource Center

Abaco - NETernity™ RM984RC VME 8-Port Unmanaged Air and Conduction Cooled Layer-2 10/100TX Ethernet Switch
  • 6U VME form factor
  • 8 10/100TX Ethernet switch rear I/O ports
  • L-2 switching at wire-speed
  • Rear ports are 10/100BaseTX
  • Air Cooled Commercial Temperature, Rugged Air Cooled Industrial Temperature and Conduction Cooled variants
  • Auto address learning
  • Auto address aging
  • Auto MDI/MDIX support
  • 10/100BaseTX auto-negotiating, supports full or half-duplex
  • Support for Jumbo Frames
  • Front panel Link and Activity status LEDs
  • RoHS compliant
  • Polyurethane or acrylic conformal coating standard for Rugged Air Cooled and Conduction Cooled boards; optional for Air Cooled Commercial Temperature
  • Serial port allows setting port speed, port duplex, port mirroring, and port disable
  • Rear Transition Module Available
KEY SPECIFICATIONS
  • MDI/MDIX control
  • RoHS 2002/95/EC compliant

Abaco - SPR507B 4-Channel Serial FPDP Interface PMC/XMC Module with PCI Express x4 Gen 2 Interface
  • Four sFPDP ports
  • Supports up to 4.25Gb/s per port
  • Each port can operate independently (direction) with a unique DMA engine per port
  • Four lane PCI Express Gen2 interface allows for high-speed data transfer to Host memory
  • Available with either PMC or XMC interface to allow for wide range of host compatibility
  • Available in five ruggedization levels with support for harsh environments and conduction cooling
  • Supports copy mode (duplicates data from one fibre to another while optionally transferring data to Host)
  • VITA 17.1 compliant, upgrade path to VITA 17.2
  • 1 GB onboard storage
  • VxWorks, Microsoft® Windows® and Linux® Software Development Kits

Advanced Illumination - DCS-103E Controller Triple Output Controller / 1 Channel per Output
  • High power in a compact package; a slim design at 115 x 121mm and only 45mm wide
  • Three Independent Outputs
  • 1-Independent Channel within each output
  • Up to 90W output power, 30W per output
  • GUI, WebServer & Command Line Tools
  • Software SDKs including: LabView, C++, C# and more
  • For pulse widths greater than 100 µsec (10 µsec resolution)
  • Overdrive currents in strobe mode limited to 5-10x

Advanced Illumination - DCS-100E Controller - Single Output Controller/3 Channels per Output
  • High power in a compact package; a slim design at 115mm x 122mm and only 22mm wide
  • Ethernet configuration options
  • Three independently controlled channels available
  • GUI, WebServer & Command Line Tools
  • Software SDKs including: LabView, C++, C# and more
  • For pulse widths greater than 100 µsec (10 µsec resolution)
  • Overdrive currents in strobe mode limited to 5-10x

Advanced Illumination - ICS 3 & 3S Inline Controller
  • The Inline Current Source (iCS 3) provides steady and optimal current to lights from a small package when a larger, more flexible external controller is not necessary.
  • Switching between continuous-on, gating on/off and strobe overdrive is seamless. The iCS 3 and iCS 3S employ Ai's exclusive Adaptive OverdriveTM that optimizes strobe power regardless of input Pulse Width.
  • The iCS 3 is a default-on device on power-up, whereas the iCS 3S is a default-off device, requiring a trigger to illuminate.
  • All iCS models employ reverse input polarity protection

Advanced Illumination - ICS 2.0 Inline Controller
  • The Inline Current Source (iCS 2) provides steady and optimal current to lights from a small package when a larger, more flexible external controller is not necessary.
  • The ICS2 provides continuous-on and DC gating on/off control as well as 0-10 volt analog dimming. 30 uSec response time.
  • All iCS models employ reverse input polarity protection.
  • A wash down version is provided with any light to which it is attached is also wash down.
  • 0 – 100% Intensity Control with optional DCS-MP, purchased separately, will provide manual intensity control via an external potentiometer.

Advanced Illumination - DCS-800E Quad X2 Controller
  • Whether you're looking to create shapes from shading using computational imaging or building a multi-point inspection line, Advanced Illumination's Quad Controllers are engineered to solve a wide variety of applications.
  • The DCS-800E provides a total of 8 channels using 2 outputs, each channel capable of firing independently. Built-in pre-programmed sequencing, allows users to progress through pre-determined recipes. This provides users the ability to automatically time a lighting sequence and output a correlated camera trigger, and to do so through multiple pre-programmed routines. As an example, by using the DCS’ frame-start signal, it is possible to synchronize a camera exposure to capture each channel as they flash in sequence.
  • Driven with Ai's proprietary SignaTech™, the DCS-800E and DCS-400E delivers peak performance while maintaining safe currents for ensured long-term stability.
  • Both Quad Controllers are housed in a compact enclosure with DIN rail mounting, delivering seamless integration into your existing machine vision system.

Abaco Systems

Abaco's history goes back more than 30 years, to the days of Plessey Microsystems in the UK – one of the first adopters worldwide of the ‘new’ VME standard. A management buyout saw Plessey become Radstone, who acquired ICS and Octec. Meanwhile, equally prominent embedded computing companies including SBS, VMIC and Condor Engineering were being acquired by GE to bolster its offering in that area – and Radstone was acquired by GE Fanuc Embedded Systems in September 2006. GE Fanuc Embedded Systems subsequently became GE Intelligent Platforms and, in September 2015, the embedded computing part of the business was acquired by Veritas Capital. The resulting business was named Abaco Systems.

We’re 700+ people, with our global headquarters in Huntsville, Alabama; a European headquarters and manufacturing site in Towcester, England; and offices throughout the world.

Tweets by @abacosys

I need help with my Abaco product

Americas

+1-800-322-3616

Europe, Africa, Middle East & Asia Pacific

+44-1327-322760

Special Avionics I/O customer hotline

+1-805-883-6097

DSP Test System

PRIVATE SUPPORT FORUM | EMAIL

Email: support@abaco.com