AVT - Alvium 1800 C-508 Embedded vision CSI-2 camera with IMX250 sensor
-
IMX250 CMOS sensor
-
ALVIUM image processing
-
MIPI CSI-2 interface
-
Various hardware options
-
Monochrome (1800 C-508m) and color (1800 C-508c) models
-
ALVIUM® Technology for on-board image processing
-
MIPI CSI-2 interface with up to 4 lanes
-
Platform concept that enables the operation of different Alvium camera models with a common software
-
Hirose HR FHH55 FPC connector with minimum space requirements for a compact design
-
Precise sensor-to-lens mount alignment
-
Standard M3 mounting holes for top and bottom mounting, standard M2 mounting holes for front mounting
-
Industrial performance for embedded vision applications
-
Easy-to-install driver and code examples
Alvium CSI-2 cameras enable new designs for embedded applications with improved image quality and reduced workload for the host. The innovative ALVIUM System on Chip (SoC) performs image corrections and preprocessing tasks onboard the camera instead of the embedded board. Unlike FPGAs commonly used in machine vision cameras, the ALVIUM SoC is extremely power efficient. With Alvium, integrating hardware and software can be done effortlessly, which ultimately reduces development time. The Sony IMX250 CMOS sensor enables imaging at 5.1 megapixel and 65 frames per second. Color models ship with an IR cut filter, monochrome models ship without a filter or protection glass.
View product page to configure camera options.
Hardware options
- Housing: Bare board or open housing
- Various lens mount: C-Mount, CS-Mount
For more information on hardware options, including product codes and technical data, such as technical drawings and mass, see the Alvium Cameras Hardware Options document.
Available accessories
- Tripod adapter
- Adapter boards connect to various embedded boards.
- FPC cables in 120 mm, 220 mm, and 420 mm length
- Various lenses
More Product Information
-
Type APS-H CMOS sensor
-
IEEE 1588 PTP
-
Power over Ethernet
-
4.59 fps at full resolution
-
Monochrome (GT5120) model
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Planarity adjusted (PA) EF Lens Mount (option -18) for electronic control of aperture and autofocus
-
Easy camera mounting via standard M3 threads at all sides and 1/4-20 tripod mounting hole
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Enhanced Defect Pixel Correction feature with a new Defective Pixel List Manager tool that allows you to load different user defined defective pixel lists to match your application and optimize the life cycle of the camera
-
Versatile temperature range for extreme environments
-
IEEE 1588 PTP
-
Power over Ethernet
-
P-Iris and DC-Iris lens control
-
Monochrome (GT1920) and color (GT1920C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Defect pixel column masking feature with the Load Defect Tables tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
IMX250 CMOS sensor
-
ALVIUM image processing
-
USB3 Vision
-
Various hardware options
-
Monochrome (1800 U-508m) and color (1800 U-508c) models
-
ALVIUM® Technology for on-board image processing
-
USB3 Vision interface for GenICam SFNC features
-
Platform concept that enables the operation of different Alvium camera models with a common software
-
Micro-B USB 3.1 Gen 1 connector with screw locks for industrial applications
-
Precise sensor-to-lens mount alignment
-
Standard M3 mounting holes for top and bottom mounting, standard M2 mounting holes for front mounting
-
Industrial performance for both embedded and machine vision applications
-
High SNR mode (up to 24 dB better signal-to-noise ratio)
-
Low-Noise Binning Mode
-
Smear reduction
-
Shading correction
-
Area of interest (AOI), separate AOI for auto features
-
Binning
-
Decimation
-
Auto gain (manual gain control: 0 to 32 dB)
-
Auto exposure (39 µs to 67 s)
-
Auto white balance
-
Look-up table (LUT)
-
Hue, saturation, color correction
-
Reverse X
-
Deferred image transport
-
Trigger programmable, level, single, bulk, programmable delay
-
Sequence mode (changes the camera settings on the fly)
-
SIS (secure image signature, time stamp for trigger, frame count)
-
Storable user sets
-
Integrated on-board image processing
-
Single board design
-
Easy hardware and software integration
-
Broad range of state-of-the-art sensors
-
Intelligent power management
-
Cost optimized design
-
APS-H optical format CMOS sensor
-
PoCXP
-
4-DIN type connector
-
79.7 fps at full resolution
-
Extended near-infrared (X-2620B NIR) model
-
Extended feature set with Sequencer Control and Multiple Region of Interest selection to support advanced imaging applications
-
On-board Defect Pixel and 2D Fixed Pattern Noise Correction for improved image quality
-
Simplified firmware update in the field via interface cables using GenICam File Access
-
Robust, fan-less design for industrial imaging applications
-
Heat-dissipation optimized housing to reduce image noise
-
Build-in tripod adapter and multiple mounting holes for eased system integration
-
DIN 1.0/2.3 CoaXPress connectors for secure operation in industrial environments
-
Single cable solution using Trigger and Power over CoaXPress
-
Comprehensive I/O functionality for extended control of connected system components
-
Select between B 270 ASG protection glass and filter types: IRC30 IR cut filter or Schneider 486 IR cut filter
-
Versatile temperature range for extreme environments
-
IEEE 1588 PTP
-
Power over Ethernet
-
P-Iris and DC-Iris lens control
-
Monochrome (GT2050) and color (GT2050C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Defect pixel masking feature with the Defect Mask Loader tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
Fast GigE Vision InGaAs SWIR camera
-
VGA resolution
-
Power over Ethernet
-
Compact industrial design, no fan
-
Up to 303 fps at full resolution
-
GigE Vision interface with Power over Ethernet
-
Comprehensive I/O control options
-
Automated on-board image correction
-
Stabilized sensor cooling, no fan
-
Extended operating temperature range
-
Compact VGA camera
-
Robust metal housing
-
Sony ICX618 CCD sensor
-
123 fps
-
Various IR cut/pass filters
-
White medical housing
Allied Vision Technologies
For more than 30 years, Allied Vision has been helping people to reach their imaging goals. Allied Vision supplies camera technology and image capture solutions for industrial inspection, medical and scientific imaging, traffic monitoring and many more application areas in digital imaging.
With a deep understanding of customers’ needs, Allied Vision finds individual solutions for every application, a practice which has made Allied Vision one of the leading camera manufacturers worldwide in the machine vision market.
The company has nine locations in Germany, Canada, the United States, Singapore and China and is represented by a network of sales partners in over 30 countries.
Contact Details
Allied Vision
102 Pickering Way - Suite 502 Exton, PA 19341, USA
Phone: +1-877-USA-1394
Fax: +1 978-225-2030