NEO NXB - 12020A Voltage / Current Breakout Test Box
- On-Off power switch
- 20 A Circuit Breaker
- 8’ Flexible Power Cord
- Outlets – (4) 5-20R
Test Tap:
- 3ft.
- (2) fork terminals (current)
- (1) fork terminals (ground)
- (2) Shielded Banana (voltage)
Multiple outlets provide flexibility in connecting equipment under test. Tester pigtail interface simplifies connecting to a variety of voltage/current measuring systems.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
120/240 | 20A | AC Line - Cord | 5-20 R [4] | Pigtail | Yes |
Application
More Product Information
- Capture from legacy to the latest video sources through support for SD analog to UHD digital formats
- Connect and switch between different video sources via Mini DisplayPort, HD-BNC, HDMI, and custom analog DVI1 connectivity
- Handle multiple video sources with the simultaneous capture of up to eight HD or two UHD streams2
- Optimize video transmission and storage through onboard multi-stream H.264 encoding
- Minimize system footprint by way of a single-slot PCIe card design
- Simplify application development using the Aurora Imaging Library, formerly Matrox Imaging Library (MIL), software development kit (SDK)
- Deploy on a current platform of choice with support for 64-bit Windows® 7/10 and Linux
-
GPS signals simulated: L1, L1C*, L2C*, L5*
-
Galileo signals simulated: E1, E5**, E5a**, E5b**
-
Simultaneous GPS/Galileo simulation
-
WAAS/EGNOS SBAS simulation
-
Static and dynamic simulations via NMEA-0183 File Record and Playback
-
12 channel configuration available with upgrade path (RAIM supported)
-
Programmable space vehicle (SV) parametrics and health
-
User or built-in GPS receiver referenced time and date
-
PVT data available via RS-232
-
User Defined Data Transferable between Linked GPSG units
-
Remote control interface Ethernet
* For tracking of L1C, L2C or L5 signals some receivers require synchronized L1 transmissions.
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
-
24-bit, delta-sigma ADC, simultaneous sampling
-
Programmable Sample Rate up to 128kSPS
-
Full, Half & Quarter Bridge with 120Ω, 350Ω & 1kΩ bridge completion
-
Voltage Excitation: 0.5V to 10V
-
Current Excitation: 0.46mA
-
2-Wire & 4-Wire Ohms/RTD
-
Bridge Zero Balancing
-
Built-In-Self-Test (BIST)
-
Strain Lead Wire Calibration
-
Shunt Calibration: 50kΩ, 100kΩ & External provided by User
-
TEDS Support
-
LXI Ethernet Interface
-
IEEE-1588 Synchronization
-
Power over Ethernet (PoE) or 10–50 V DC input
-
Built-in Parallel Data Streaming
-
Full-featured Embedded Web Interface
-
Compact 1U Half-rack Form Factor
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
3KVA, 3KW Double Conversion On Line Isolated 115VAC Input UPS, and simultaneous 120 and 240VAC 60Hz Output, Power Factor Correction, Extended Internal Batteries, SNMP Communications for Military Applications
-
Verify quality of optical fiber cable assemblies, connectors and short-run networks
-
Troubleshoot and distinguish between macro-bends, splices, connectors and breaks
-
Locate insertion loss points – save hours of troubleshooting time
-
Verify return loss of multiple points in a fiber assembly or harness simultaneously
-
Verify and maintain aircraft and shipboard networks
-
Customize GUI for automated pass/fail verification of your fiber assembly using software development kit
-
32GTps, PCIe 5.0 data rate operation. Fully compatible with other PCIe data rates of 2.5, 5.0, 8.0 and 16 GTps
-
Link widths to 16-lanes, including 1-, 2-, 4-, 8-lanes
-
256GB memory (128GB upstream and 128GB downstream)
-
Memory segmentation for capture of multiple traces
-
Host-Client connection for remote debugging using Ethernet or local debugging using USB
-
SMB capture and trigger for NVMe Management Interface (NVMe-MI) observability
-
Simultaneous capture of multiple links is allowed with multiple simultaneous users
-
Decodes all PCIe, NVMe and CXL traffic at all layers of the stack including the TLP, DLLP, and PHY layer packets
-
Flexible trigger events include training sequences, ordered sets, queue pairs, PRPs, SGL, SMB, etc.
-
Cascade captures from up to four Xgig chassis into a single trace view
-
Full support of PCI Express LTSSM analysis
-
Field replaceable power supply
-
LEDs give quick indicators of power and link status
-
Includes one-year hardware and three-year software warranties
-
Works with the VIAVI Xgig software tool suite: Trace Control, Trace View, Expert™, Serialytics™
-
Supported by a wide variety of Interposers (CEM, U.3, etc.)
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.
Test & Measurement
Download Line Card
Document