NEO NXB - 12020B Voltage / Current Breakout Test Box
-
On-Off power switch
-
20 A Circuit Breaker
-
Outlets – (2) Universal
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
Multiple outlets provide flexibility in connecting equipment under test. Tester pigtail interface simplifies connecting to a variety of voltage/current measuring systems.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
120/240 | 20A | C14 Inlet | Universal | Pigtail | Yes |
More Product Information
-
32 GT/s, PCIe 5.0 data rate operation. Fully compatible with other PCIe data rates of 2.5, 5.0, 8.0 and 16.0GTps
-
Link widths up to 8-lanes
-
Memory segmentation for capture of multiple traces
-
Simultaneous two-link, dual port capture is allowed by multiple users
-
Host-Client connection for remote debugging using Ethernet, or local debugging using USB
-
Decodes all PCIe and NVMe traffic at all layers of the stack including the TLP, DLLP, and PHY layer logic sub-blocks
-
Trigger and Search events include training sequences, ordered sets, queue pairs, PRPs, Scatter/ Gather Lists (SGL) etc.
-
Cascade up to four Xgig captures into a single trace view
-
Full support of LTSSM for analysis
-
Field replaceable modular fan and power supply assemblies
-
LED’s give quick indicators of power and status
-
Works with the VIAVI Xgig software tool suite: Trace Control, Trace View, Expert™, Serialytics™
-
High responsiveness following to the image can be realized because of the image recognition setting according to colors on the sensor part.
-
Composite strength distribution of the actual image taken by the camera and the measured data can be visualized.
-
3KVA, 3KW Double Conversion On Line Isolated 115VAC Input UPS, and simultaneous 120 and 240VAC 60Hz Output, Power Factor Correction, Extended Internal Batteries, SNMP Communications for Military Applications
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
We subject our amplifiers to the harshest conditions just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 W that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications.
These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers.
These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
Flexible setup for different measurements
-
Simultaneous measurement of DGD, SOPMD, PDL
-
Jones or Mueller Matrix methods
-
Free space PSA input enables absolute SOP measurements
-
GPIB control of external lasers
-
Interface-independent
-
Simple image acquisition of greyscale, color, and temperature images
-
Comprehensive camera control
-
Statistical image evaluation
-
Save as RAW, TIF, BMP, AVI, and more file formats
-
Pseudo color IR image display inclusive temperature measurement
-
Simultaneous analysis of several user-defined ROIs
-
Support for important image pre-processing functions (look-up tables, background correction, mirroring etc.)
- Capture from legacy to the latest video sources through support for SD analog to UHD digital formats
- Connect and switch between different video sources via Mini DisplayPort, HD-BNC, HDMI, and custom analog DVI1 connectivity
- Handle multiple video sources with the simultaneous capture of up to eight HD or two UHD streams2
- Optimize video transmission and storage through onboard multi-stream H.264 encoding
- Minimize system footprint by way of a single-slot PCIe card design
- Simplify application development using the Aurora Imaging Library, formerly Matrox Imaging Library (MIL), software development kit (SDK)
- Deploy on a current platform of choice with support for 64-bit Windows® 7/10 and Linux
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.