NEO NXB - 20830 Voltage / Current Breakout Test Box
-
On-Off power switch
-
30 A Circuit Breaker
-
Inlet - NEMA L6-30
-
Outlets – NEMA L6-30R
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
208 | 30A | L6-30 - Cord | L6-30 R | Pigtail | Yes |
More Product Information
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
On-Off power switch
-
15 A Circuit Breaker
-
Inlet - IEC C14 for use with any cordset
-
Outlets – (8) IEC C13
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
-
High responsiveness following to the image can be realized because of the image recognition setting according to colors on the sensor part.
-
Composite strength distribution of the actual image taken by the camera and the measured data can be visualized.
-
GPS signals simulated: L1, L1C*, L2C*, L5*
-
Galileo signals simulated: E1, E5**, E5a**, E5b**
-
Simultaneous GPS/Galileo simulation
-
WAAS/EGNOS SBAS simulation
-
Static and dynamic simulations via NMEA-0183 File Record and Playback
-
12 channel configuration available with upgrade path (RAIM supported)
-
Programmable space vehicle (SV) parametrics and health
-
User or built-in GPS receiver referenced time and date
-
PVT data available via RS-232
-
User Defined Data Transferable between Linked GPSG units
-
Remote control interface Ethernet
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
We subject our amplifiers to the harshest conditions just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 W that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications.
These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers.
These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.