NH Research - S450 Series Functional Test System - Production Test Systems for High Speed Power Supply Testing

NH Research - S450 Series Functional Test System - Production Test Systems for High Speed Power Supply TestingNH Research - S450 Series Functional Test System - Production Test Systems for High Speed Power Supply Testing
  • Preconfigured fully-capability test system in a 35” rack
  • Interchangeable DC loads and sources
  • Embedded Measurement System (EMS)
    – 100 kSamp/s waveform capture
    – 12 channel measurement system
  • emPower™ test executive control
    – PC/Serial interface
    – USB-Serial ∓ LAN-Serial available

More

Applications

The Power Supply Functional Test System S450 Series is based on a S430 Production Test System and adds higher power AC/DC sources and higher power DC loading options. This system maintains the features of the S430, is PC-controlled, full-capability and highly flexible system suitable for high-speed testing of power supplies typically used in high volume consumer applications.

The key to flexibility, as well as space- saving design, is the modular DC load/source mainframe. This is the portion of all testers where flexibility is most often required. What makes this subsystem unique is that the 6-slot chassis will accept any combination of electronic loads and/or DC source modules.

Additional flexibility is gained through the ability to synchronously parallel like modules from within a test program to match each supply-under-test’s specific stimulus requirements. In this manner, it is possible to configure a wide range of virtual loads and sources within the chassis’ limits. All modules also have wide operating ranges and constant power operating envelopes to allow covering a maximum range of requirements through a minimum group of modules.

More Product Information

NH Research - S400 Series Modular Test Systems - for Power Supply Production Testing, High Speed Testing, & More!
  • Full-capability test system in a 6-slot chassis for interchangeable loads and DC sources
  • 3-sizes of compact, space-saving cabinets
  • Embedded measurement system with 12 input channels and 100kSamp/sec waveform capture
  • emPower™ Test Executive
  • PC-LAN control

NH Research - 5710 Series Engineering Characterization Test System - DC Power Supply Test System for Engineering Characterization/Design Verification Testing, Power Supplies Testing, Defense Avionics Testing, & More!
  • NEW! Tektronix MDO-Series Mixed Signal Oscilloscope
  • Unlimited voltage, current & timing measurements relative to digital signals.
  • Library of design verification test routines reduces program development time
  • Configuration flexibility

NH Research - S600 Series Multi Channel Power Supply Tester - Multi-Channel Test System for High-Speed Parallel Testing of Adapters, Chargers, LED Power Drivers, DC Converters, Voltage Regulator Modules, Point-of-Load Converters & AC-DC Power Supplies
  • Maximum test throughput through parallel testing of multiple devices & outputs
  • Ease of reconfiguration or expansion through front-loading, card-based instruments
  • Built-in waveform digitizers on all instruments
  • Space-saving design
  • emPower® Test Executive

NH Research - 9210 Series Single Channel Battery Test System - Modular, Regenerative Battery Test System for Automated Characterization Testing, Power Cycling Testing, Life-Cycle Testing & More!
  • Smaller footprint makes it easier to move within a lab (roughly half the size of the 9200)
  • Custom waveform/profile generation
  • Sub-mS voltage, current & mode transition times
  • Built-in digital measurements with charting & scope displays
  • Internal controller with software & connections for an external monitor & keyboard
  • Bidirectional DC Source, expandable from 12 to 252kW with 40, 120, or 600V
  • Regenerative, 87% efficiency of discharge power returned to AC mains
  • Multiple safety layers to protect battery being tested
  • Battery emulation & burn-in applications
  • Create, run, monitor, chart & report UUT profiles without writing any code

NH Research - 5500 Series Universal UPS Test System - Universal UPS/Inverter Test System for Testing Power Supplies with AC Outputs Found in Uninterruptable Power Supplies (UPS) & Inverters
  • Digital measurement system (DMS)
    – 2 waveform digitizers
    – 2×16, 100MHz multiplexer
    – Expandable input measurement channels
  • Maximum configuration flexibility
  • Turn-key test system with included test controller
    emPower™ test executive

NH Research - 9300 Series High-Voltage Battery Test System - Modular, Regenerative Battery Test System with Power Range from 100kW up to 2.4MW
  • Wide Operating Envelope at 100kW per cabinet
  • Scalable to 1.2MW/4000A
  • Regenerative, greater than 90% efficiency of discharge power returned to AC mains
  • Built-in digital measurements with charting & scope displays
  • Current, Voltage & Mode transitions in <2 mSec
  • Battery Emulation Mode
  • Touch Panel, LabVIEW® & IVI Drivers
  • Enerchron® Test Executive

NH Research - 5600 Series Universal Test System - for Testing Power Supplies with DC Outputs
  • Maximum configuration flexibility with multi-bay capacity
  • Digital measurement system 2 Waveform digitizers and 2×16, 100 MHz multiplexer
  • Expandable input measurement channels
  • Common interface panel
  • emPower™ Test Executive

NH Research - 9220 Series Low Voltage/High Current Battery Charge/Discharge Test System - Regenerative Battery Cycler, Power Cycling, & Life-Cycle Testing of Low Voltage/High Current Batteries
  • Single output up to 40V/3,600A/72kW per system
  • Parallel expansion up to 7,200A
  • Built-in digital measurements including Ah & kWh
  • Multiple safety layers to protect battery/DUT
  • SCPI, VXI-11, & LabVIEW control via LAN interface
  • NI-Compliant LabVIEW Drivers
  • Regenerative, 87% efficiency returning discharge power to facility
  • Bidirectional DC Source, Battery emulation and burn-in applications
  • Crane/hoist lifting hangers & robust casters

NH Research - 9420 Series AC Power Source - AC Source with HiVAR® Technology Ideal for ATE use in Aviation, Aerospace, Defense, Military/Mission Critical Testing, Manufacturing Test, Research & Development & More!
  • Voltage Range – 175/350VRMS, 200/400VDC
  • 7 models – 8kW/21kVA to 96kW/252kVA
  • Unique configuration flexibility provides for single, split, three-phase operation plus full-power DC
  • HiVAR design eliminates derating nominal power due to reactive loads
  • Frequency – 30 to 880Hz
  • High-resolution waveform digitizer & scope display
  • Precision ultra-low current measurements
  • Seamless, constant-power operating envelope
  • Built-in 9” touch-panel user interface for manual control & measurement display
  • Graphical waveform editor for user-defined waveforms
  • High-level line disturbance programming Macros
  • External PC option to host NHR emPower® Test Sequencer
  • Alternate programming in LabVIEW, native SCPI, & other IVI-compliant languages
  • Improved power density results in half the panel height of a traditional AC source