Sorensen - SLH AC/DC High Power AC + DC programmable electronic load
-
Flexible Product Line
-
Low power DC modules
-
Low power AC modules
-
High power DC, 19" rack mounted loads
-
High power AC, 19" rack mounted loads
-
26 Total Models
-
-
Flexible Control
-
Remote: GPIB, RS-232, Analog
-
Manual: Front Panel
-
DC Modes: CC, CR, CV, CP
-
AC Modes: CR, CC with crest factor control
-
Dynamic mode with slew rate control
-
-
Flexible Data Feedback
-
GPIB, RS-232
-
Current monitor output (SLM DC only)
-
Front panel
-
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
The SLH Family is made up of fully programmable, high power AC or DC electronic loads. The 500V models are for PFC testing, power transformers and various other AC or DC power sources. The 300V models are used for testing of UPSs, automatic voltage regulators (AVR), and batteries.
- High current, 60V DC models for general purpose power supply testing
- High voltage, AC/DC models are intended for inverter test, Power Factor Correction (PFC) circuit testing (500V) and UPS testing (300V)
More Product Information
-
500 watts CW
-
100kHz–1000MHz
-
Class A
-
Portable
-
Full VSWR– tolerant
-
CE & RoHS Compliant
-
High Efficiency
-
Model FM7004A Field Monitor
-
Model FL7218/Kit Electric Field Probe Kit (supplied with data from an accredited lab)
-
Easy to Use
-
No need to break the circuit or insert a shunt
-
Small form factors for use on crowded boards
-
-
Variety of Applications
-
Bandwidths up to 100 MHz
-
Peak currents up to 700 A
-
Sensitivities down to 1mA/div
-
-
High Precision Measurements
-
Low frequency accuracy of 1%
-
Integrated autozero capability
-
-
Fully Integrated with Teledyne LeCroy Oscilloscope
-
No additonal hardware is required
-
Power is supplied from oscilloscope ProBus connection
-
Automatic display of waveforms in Amps and calculated power traces scaled correctly in Watts
-
Degauss and Autozero directly from oscilloscope user interface
-
-
DCS025 Deskew Calibration Source
-
Provides ability to precisely deskew most voltage probes along with 30, 150 and 500A current probes
-
-
Can help to stabilize oscillations in high-gain devices
-
Impedance match to low dynamic resistance laser diodes
-
Custom configured for your application
-
Operates up to 32GTps at PCIe 5.0 data rates
-
Downward compatible with PCIe data rates of 2.5, 5.0, 8.0 and 16.0GTps
-
Supports link widths up to 16-lanes
-
CEM adapter card endpoint DUT devices plug directly into the Test Stand
-
Includes cables for Analyzer connection
-
Supports Analyzer side-band signal capture and triggering with display in multiple formats
-
Data path uses high-speed re-drivers to ensure good signaling
-
Supports automatic link tuning for optimum communication and lowest BER
-
Modular, replaceable 600W power supply powers Test Stand and DUT
-
Supports testing of high-power graphics cards
-
LEDs give quick indicators of power and status
-
Size: Base Pod: 120 x 162 x 30 mm (DxWxH)
-
Works with the VIAVI Xgig5P-PCIe5-X16-PF Analyzer/Exerciser chassis platform
-
Supported by VIAVI Xgig™ Analysis tools for test setup, trace capture, protocol evaluation, etc.
-
Provides consistent, repeatable capture of link training, equalization negotiation and other information
-
Affordable GigE Vision InGaAs SWIR camera
-
QVGA resolution
-
Power over Ethernet
-
Compact industrial design, no fan
-
Up to 344 fps at full resolution
-
GigE Vision interface with PoE+
-
Comprehensive I/O control options
-
Automated on-board image correction
-
Stabilized sensor-cooling, no fan
-
Extended operating temperature range
-
Flexible Product Line
-
Low power DC modules
-
Low power AC modules
-
High power DC, 19" rack mounted loads
-
High power AC, 19" rack mounted loads
-
26 Total Models
-
-
Flexible Control
-
Remote: GPIB, RS-232, Analog
-
Manual: Front Panel
-
DC Modes: CC, CR, CV, CP
-
AC Modes: CR, CC with crest factor control
-
Dynamic mode with slew rate control
-
-
Flexible Data Feedback
-
GPIB, RS-232
-
Current monitor output (SLM DC only)
-
Front panel
-
-
650VA, 500W, 120VAC 60Hz Input and 120VAC 60Hz Output, Frequency Changer, Non-Isolated, Power Factor Corrected, 1/2 Rack Unit, 3U High x 8.5" Wide x 17" Deep, Rugged, Double Conversion, to Provide Power Conditioning and Hot Swap Battery Hold-up for Industrial Applications
-
Advanced MicroVac chuck surface for minimum contact resistance between wafer and chuck
-
Safety-rated interlock system for high-power testing (meets EN 60947-5-1, EN 60204-1)
-
Supports fully automated testing up to 10kV by eliminating arcing point
-
Full wafer access via locking roll-out stage
-
On-wafer power device characterization up to 10,000 V DC / 600 A
-
Coaxial, triaxial, and pin jack feed-troughs available
-
Convenient instrument connection kits
-
Load/unload wafer to hot/cold chuck (-60° C to +300° C)
-
Up to 15% faster transition times than other systems in the market
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries