• Directly compatible with most commercial VNA’s
• Available as polynomial and characterized device kits
• Measure S-Parameters with uncertainty when used in conjunction with Maury’s Insight software platform

Maury offers coaxial and waveguide VNA calibration kits.

Coaxial calibration kits are offered in Polynomial SOLT, Characterized Device (CD) SOLT, and TRL, depending on the connector series. Where available, CD kits improve calibration accuracy when compared to SOLT kits based on polynomial definitions as each calibration kit is provided with individually characterized short, open and fixed load standards, whose S-parameters can be loaded into commercial VNAs directly or when used with Maury’s Insight™ software platform. When combined with Insight™, users will be able to quantify the uncertainty contribution of their calibration kit to their overall measurements. CD cal kits result in TRL-like accuracy with fixed-load SOLT ease-of-use.

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

A precision fixed termination (or load) consists of an immovable, (fixed) termination which, when mated to the end of a trans-mission line or cable, absorbs nearly all of the signal energy traveling toward it. An ideal “matched” condition exists when a termination with an impedance value of Z0, is connected to the end of a transmission line or cable that also has a characteristic impedance of Z0. Such an ideal “matched” condition (one with no mismatch between the termination and its mated line or cable) is critical if a voltage standing wave ratio (VSWR) of 1.0:1 is to be achieved in a system with a 50 or 75 ohm impedance value. Simply put, the more closely the 1.0:1 ratio is approached, the more accurate the measurements that can be made from a system.

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

Fixed flush and fixed offset short circuit terminations (shorts) are used to establish reference planes in transmission systems and as key elements in the calibration of vector network analyzers (VNAs). Offset shorts can be used for banded calibrations of VNA. Those with the longest offset are often used to evaluate the calibration effectiveness of a VNA by measuring the effective source match after calibration.

• Excellent temperature and voltage stability
• Units for noise figure meters feature 15.5-dB ± 0.75 dB ENR output
• High-output units for radar and satellite communications system testing feature output between 26 and 35 dB ± 1 dB ENR

The NC3000 Series calibrated coaxial AWGN sources are well suited for receiver testing, noise figure measurements, or applications that require broadband noise and fast switching times. Several models include output isolators, and voltage regulators that provide excellent stability over varying temperature and voltage ranges. The NC3000 Series includes the NC3100 units with 15 dB ENR output for noise-figure meters, and the NC3200 Series high-output noise sources with outputs between 26 and 35 dB ENR for radar and satellite communications system testing.

The VectorStar ME7838 Series broadband VNA offers the widest available single frequency sweep from 70 kHz to 110, (ME7838AX to 125), (ME7838EX to 125), to 145 GHz, and to 220 GHz with mmWave bands to 1.1 THz. 

• The ME7838AX or ME7838EX version can easily be upgraded to 145 GHz and to 220 GHz
• All versions may be configured to include banded millimeter-wave modules up to 1.1 THz
• Industry-best calibration and measurement stability: 0.1 dB vs 0.6 dB over 24 hrs.
• All versions support the 3744x-Rx receiver for noise figure measurements, including the ability to characterize differential noise figure, to 125 GHz
• Compact, lightweight mmWave modules (0.6 lb vs 7+ lbs and 1/50 the volume) offer low cost installation on smaller probe stations.

• Ideal probe for up to 48 V power conversion
  • 250, 500 MHz and 1 GHz bandwidth
  • 80 V dynamic range
  • 60 V common mode
• Highest accuracy
  • 0.5% gain accuracy
  • Precision gain calibration
  • Best LF flatness (0.1 dB)
• Lowest noise and highest rejection
• Wide variety of tips
  • High performance solder-in
  • Browser
  • Single pins and header
  • Mini and micro grabbers
  • Socketed connections
  • High temp solder-in
  • Y-banana adaptor
• ProBus active probe interface

• 1-port VNA with frequency options from 150 kHz to 6 GHz
• External PC control enables control of multiple ShockLine MS46121B devices in parallel for excellent multisite throughput
• Very compact package allows for direct connection to the DUT
• Scalar transmission measurements in a (1-to-1) or (1-to-n) configuration
• No on-board data storage eliminates the need for data purging in secure applications
• Standard bandpass time domain with time gating enables easier and faster fault identification
• A common GUI interface within the ShockLine family reduces switching costs between models

VNA Master MS2036C (5 kHz to 6 GHz)

• True 2-Path 2-Port Vector Network Analyzer
• Ultimate accuracy with 12-term error correction algorithm
• User-defined Quad Display for viewing all 4 S-parameters

+ Spectrum Analyzer (9 kHz to 9 GHz)

• Detectors: Peak, Negative, Sample, Quasi-peak, and true RMS
• Markers: 6, each with a Delta Marker, or 1 Reference with 6 Deltas
• Built-in pre-selector for eliminating spurious in displays
• PIM Hunting

• Standard three-year warranty (battery one-year warranty)

• Output White Gaussian noise
• Output power up to +30 dBm
• 127 dB of attenuation; 0.1 dB step size
• Units > 2 GHz have total attenuation of 79.9 dB
• Low distortion signal path
• Power 115 VAC, 60 Hz
• Noise attenuator accuracy: ±0.2 dB or 0.5% at 1 – 500 MHz ±0.2 dB or 1% at 0.5 – 1.0 GHz ±0.3 dB or 2% at 1 – 2 GHz
• Standard connectors SMA female
• 7” touch screen display
• Dimensions: 17.25 in. wide x 6.50 in. including feet, high x 19.50 in. deep
• Removable hard drive for added security
• Operating Temperature: -10° to +65°C