• Supports PCI Express Rev 2.0 x4 or higher, backwards compatible with PCIe Rev 1.10 slots 
• Up to 512MB of high-speed image memory 
• Single slot solution with reconfigurable camera control and general purpose input/outputs

With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.

• Ideal probe for up to 48 V power conversion
  • 250, 500 MHz and 1 GHz bandwidth
  • 80 V dynamic range
  • 60 V common mode
• Highest accuracy
  • 0.5% gain accuracy
  • Precision gain calibration
  • Best LF flatness (0.1 dB)
• Lowest noise and highest rejection
• Wide variety of tips
  • High performance solder-in
  • Browser
  • Single pins and header
  • Mini and micro grabbers
  • Socketed connections
  • High temp solder-in
  • Y-banana adaptor
• ProBus active probe interface

• 150 MHz, 2 analog channels
• 8 synchronized digital channels (T3AWG2152-D only)
• 16-bit vertical resolution
• 128 MPts @Ch waveform memory
• Max sampling rate of 600 MS/s

An affordable yet high performance solution for all AFG and AWG functions, specializing in key applications such as Automotive Ethernet Transmitter Distortion Test and Double Pulse Testing. The 8 synchronized digital channels (T3AWG2152-D only) are ideal for digital design debugging and validation.

With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.

• 5 GigE Ethernet port & hardware
• Supports cable lengths up to 100 m (CAT-5e, CAT-6) or (4T-6A)
• Simplified set-up with field proven Sapera LT software featuring CamExpert
• Engineered to accommodate industrial environment with a ruggedized screw mount RJ-45 connector

• Highest resolution – 12 bits all the time
• More channels, flexibility – 8 analog and 16 digital channels
• Longest Memory – 5 Gpt records with simple navigation – no compromise
• View 16 channels on one display with OscilloSYNC™
• Powerful, deep toolbox enables and simplifies complex analysis
• MAUI with OneTouch user interface for intuitive and efficient operation
• Zone Trigger – Simple Triggering for Complex Signals

• Up to 4 GHz Bandwidth 
• ±60 V Offset Capability 
• ±800 mV Dynamic Range 
• 50 kΩ DC Input Impedance 
• 1.2x Attenuation for low additive noise 
• MCX terminated cable with wide variety of connections: 
  • Solder-in (4 GHz) 
  • Coaxial Cable to U.FL receptacle (3 GHz) 
  • MCX PCB Mount (4 GHz) 
  • Browser (500 MHz) 
• ProBus Interface

Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.