Products

Displaying 1 - 25 of 44

Teledyne LeCroy Probe Parts and Kits

There are a variety of replacement and additional probe parts, tips and accessories

Yokogawa 366921 BNC to Banana-Jack (Female) Adapter 42V

BNC-Banana-jack (female) adapter. Use for circuits having voltage levels no greater than 42 V.

Yokogawa 366922 BNC to Banana (Male) Adapter

Banana-plug (male)-BNC adapter. Use for circuits having voltage levels no greater than 42 V.

Yokogawa 366923 BNC to T Adapter

T-adapter for BNC connectors. Use for circuits having voltage levels no greater than 42 V.

Yokogawa 366924 BNC to BNC 1M Cable

BNC-BNC 1m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.

Yokogawa 366925 BNC to BNC 2M Cable

BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.

Yokogawa 366926 BNC to Alligator 1M Cable, 1:1

A 1 m long BNC-alligator clip cable.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for DL750/DL750P, SL1000 & SL1400

Yokogawa 366961 Banana to Alligator 1.2M Cable, 1:1

  • A subassembly of 1.2 m long test leads with alligator-clip adapters.
  • Use only for circuits having voltage levels no greater than 42 V.
  • Applicable for SL1000 & SL1400.

Yokogawa 366973 GO/NO-GO Cable

This cable is used to connect an external device. Do not use this cable for purposes other than DL750/1600/1700/1700E/7400 GO/NO-GO judgement.

Yokogawa 700940 MIL-C-26482 to NDIS Conversion Cable

A 1.5 m long connector-to-connector adapter cable complying with NDIS-MIL C26482. Used to connect a MIL-standard cable to the strain module.

Yokogawa 700976 50 Ω Terminator

  • Used to connect an oscilloscope having a 1M-ohm input to a probe with a 50-ohm output.
  • It is required when using the 701920 and 701922 probes with the DL1600 series.

Yokogawa 701901 BNC to Safety Banana 1.8M Cable, 1:1

1000 Vrms-CAT II, 1.8 m long
Safety BNC(male) to safety banana(female) use in combination with 701959, 701954, 758921, 758922 or 758929.
Applicable for DL750/DL750P, SL1000, SL1400

Yokogawa 701902/701903 Safety BNC to BNC Cable 1M/2M

  • 701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
  • 701903: 1000 Vrms-CAT II (BNC-BNC), 2 m
  • Applicable for DL750/DL750P, SL1000 & SL1400.

Yokogawa 701906 Long Test Clip

  • Set contains one black and one red clip
  • 1000 Vrms-CAT II
  • 2 pieces (red and black) in 1 set
  • Connected to the 758933, 758917, or 701901
  • Length: 0.3m
  • Applicable for DL750/DL750P, SL1000, SL1400

Yokogawa 701915 Active Probe Clip Accessories Kit

  • This attachment set can be used with PBA2500 and PBD2000.
  • Spring pin (straight) x 4
  • Spring pin (angle) x 4
  • Pin (straight) x 20
  • Pin (angle) x 20
  • Pin (L shape) x 2
  • Micro Clip (black) x 1
  • Micro Clip (red) x 1
  • Single lead (black) x 1
  • Single lead (red) x 1

Yokogawa 701919 Probe Stand

Using a probe stand with a flexible arm and heavy base to hold and stabilize probes can simplify circuit board testing, A probe stand gives you stable, pinpoint probing control for high density or three handed operations.

Yokogawa 701934 External Probe Power Supply

A power supply for current probes, FET probes, and differential probes. Supplies power for up to four probes, including large current probes.

Yokogawa 701936 Deskew Correction Signal Source

When using different types of probes, such as a voltage probe and a current probe, a small propagation delay difference exists between the probe pair. Small, but significant, this difference is caused by each probe's unique internal circuitry and cable length. This propagation delay difference is known as ‘skew' and creates an error when calculating switching loss or measuring timing. In the high speed switching of the switching power supply, the engineer is required to measure the timing of the control signal in nano seconds.
The 701936 Deskew correction signal source provides time synchronized current and voltage sources, which are necessary to calibrate and remove the skew characteristics from your oscilloscope-based power analysis measurements.

Yokogawa 701948 Extension Clip Accessories

  • Connected to the 700929, 701947
  • Maximum input voltage: 1,000V (DC + ACpeak)
  • Length: 0.26m/0.3m/0.4m
  • Applicable for DL750/DL750P, SL1000, SL1400

Yokogawa 701954 Large Alligator Clip (Dolphin Type)

  • Set contains one black and one red clip.
  • 1000 Vrms-CAT II.
  • Applicable for DL750/DL750P, SL1000 and SL1400

Yokogawa 701955/701956 NDIS Bridge Heads

  • NDIS cable (5 m) included
  • Applicable for DL850 series, DL750/DL750P, SL1000 & SL1400

Yokogawa 701957/701958 D-Sub Bridge Heads 120Ω/350Ω

  • D-sub cable (5 m) included
  • Supports Shunt-Cal
  • Applicable for DL850 series, DL750/DL750P, SL1000 & SL1400.

Yokogawa 701959 Safety Mini Clip (Hook Type)

  • Safety terminal (banana female)-to-mini clip adapter
  • 2 pieces (red and black) in 1 set Rating: 1000 V CAT II Connected to the 758933, 758917, or 701901.
  • Applicable for SL1000 and SL1400.

Yokogawa 701963 Soft Carrying Case for DL850E Series

Three pockets are provided for storing accessories and the user’s manu

Yokogawa 701966 Printer Roll Paper for DL750P and SL1400

  • Quality paper for the DL750P and the SL1400.
  • Paper width: 210 mm (A4 size)
  • Paper length: 20 m
  • Order Qty: 6 (1set)

Pages