Products

Displaying 1 - 25 of 45

Abaco PMC-422 Serial Controller - 8-port PMC for VME, CompactPCI

  • 4 RS232 ports can be accessible via front RJ45 connectors
  • All ports accessible on rear I/O J4 with PMC I/O Module (PIM) PIM422
  • 8 high-performance 16C550 UARTs with 64 bytes of RX/RX FIFO per channel
  • PMC form factor
  • PCI bus 2.2 target interface compliant up to 33MHz clock, 32-bit bus
  • 8 port RS232/RS422/RS485 serial controller

Abaco PMC-OCTPRO-232 Mezzanine Card - Expands eight RS-232 channels

  • PMC with eight RS-232 asynchronous serial channels
  • Data rates to 115.2 kbaud
  • I/O via front- or back-panel P4 connectors
  • 128-byte FIFOs for receive and transmit on each channel
  • Linux, VxWorks and Windows NT drivers available

Abaco PMC-OCTPRO-422 PCI Mezzanine Card - Expands eight RS-422 channels

  • PMC with eight RS-422 asynchronous serial channels
  • Data rates to 460.8 kbaud
  • I/O via front- or back-panel P4 connectors
  • 128-byte FIFOs for receive and transmit on each channel
  • Linux, VxWorks, and Windows NT drivers available

Abaco VME-1111 Digital Input Board 64-bit high voltage with BIT

  • Double Eurocard form factor
  • 8-, 16-, or 32-bit data transfers
  • RS-422/RS-485-compatible differential line receivers provide ±7V noise immunity
  • User-selectable input voltage thresholds (1.25 to 66 V)
  • Front panel with fail LED
  • 4 bits of differential or high-voltage digital inputs
  • Each group of 32 inputs is jumper-selectable to monitor: contact closure, voltage source, current sinking, or differential signals
  • On-board Built-in-Test logic for fault detection and isolation
  • Open circuit provides logic zero or (jumper-selectable) logic one
  • Input filter option

Abaco VME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test

  • Complies with the VMEbus Specification Rev. C.1
  • High reliability DIN-type I/O connectors
  • Double Eurocard form factor (6U)
  • Open circuit provides logic zero or (jumper-selectable) logic one
  • A24:A16:D32/D16/D08 (EO): slave: 39/3D:29/2D
  • Front panel with fail LED
  • On-board Built-in-Test logic for fault detection and isolation
  • Each group of eight inputs is jumper selectable to monitor voltage source or current sinking signals
  • 128 bits of high-voltage digital inputs

Abaco VME-1129 Digital Input Board 128-bit high voltage

  • MTBF: 136,969 hours (217F)
  • Front panel with fail LED
  • Double Eurocard form factor (6U)
  • 128 bits of high-voltage digital inputs
  • 3 ms input noise suppression filter
  • Each group of eight inputs are jumper-selectable to monitor voltage source or current sinking signals
  • On-board Built-in-Test logic for fault detection and isolation
  • User-selectable input voltage thresholds (0.67 to 31 V)
  • A24:A16: D32/D16/D08 (EO): slave: 39/3D:29/2D
  • VMEbus compatible (ANSI/IEEE STD 1014-1987 IEC 821 and 297)

Abaco VME-1150B Digital Input Board - 64-bit Optically Coupled

  • Sixty-four optically coupled digital inputs
  • 5 V to 48 VDC input range
  • High isolation, 1000 V sustained, 2000 V pulsed
  • Filtered input options
  • Dual I/O connectors
  • Contact closure sensing
  • Voltage  souring or current sinking input options
  • Positive or negative true input options
  • Double Eurocard form factor with front panel access
  • 8- or 16-bit data transfers
  • Nonprivileged or supervisory I/O access
  • High reliability DIN-compatible input connectors

Abaco VME-1182A 64-Channel Isolated Digital Input Board with Multifunctional Intelligent Controller

  • Interrupt level is user selected
  • Complies with ANSI/IEEE STD C37.90.1-1989 surge protection when used with companion suppression panel (e.g., VME-3459)
  • 64 optically isolated inputs
  • Multifunctions available per channel: COS; SOE; pulse accumulation; programmable debounce times; time tagging
  • Short or standard, supervisory, nonprivileged, or either access
  • COS selections (disabled), rising edge (low-to-high transition), falling edge (high-to-low transition), or any edge
  • COS functions software controlled on a channel-by-channel basis
  • 1.0 ms measurement resolution
  • Debounce times software controlled on channel-by-channel basis
  • Pulse accumulation (0 to 65,535 pulses)
  • SOEs monitoring on channel-by-channel basis
  • 5 to 60 VDC or 110 to 240 VAC
  • 1,500 VDC or 1,100 VRMS channel-to-channel and channel-to-VMEbus isolation

Abaco VME-2120 64-bit High Voltage Digital Output with Built-in-Test

  • 8-, 16-, or 32-bit transfers
  • High reliability DIN-type I/O connectors
  • Compatible with Intelligent I/O Controllers
  • Output clamp diodes for inductive flyback protection
  • High breakdown voltage (55V)
  • or inductive loads
  • Automatic surge current shutdown protection option
  • Thermal shutdown protection option for driving incandescent
  • High current drivers (600mA sink)
  • 64 bits of high voltage outputs

Abaco VME-2128 128-bit High-Voltage Digital Output Board with Built-in-Test

  • Front panel with fail LED
  • Sockets are provided for warming resistors, which are supplied by the user
  • Optional pull-up resistors for electronic switch outputs
  • A24:A16:D32/D16/D08 (EO): slave 39/3D:29/2D:6U form factor
  • VMEbus compatible (ANSI/IEEE STD 1014-1987 IEC 821 and 297)
  • Thermal shutdown protection
  • High breakdown voltage (55 V)
  • Output clamp diodes for inductive flyback protection
  • Compatible with Intelligent I/O Controllers
  • Built-in-Test logic for fault isolation
  • High-current drivers (600 mA sink)
  • Automatic surge current shutdown protection
  • 128 bits of high-voltage outputs

Abaco VME-2131 64-bit High Current Source/Sink Driver Board

  • Front panel Fail LED
  • Double Eurocard form factor
  • Outputs are jumper-selectable for source/high-Z or source/sink operations
  • High reliability DIN-type output connectors
  • Software compatible with VMIVME-2120
  • Compatible with Intelligent I/O Controllers
  • Built-in-Test logic for fault isolation
  • 8-, 16-, or 32-bit transfers
  • High breakdown voltage (35 V minimum)
  • Thermal shutdown protection
  • Output transient protected
  • ±3.5 A peak output current (100 ms, 10 percent DC)
  • 500 mA continuous source only or source/sink current (fan cooled)
  • 64 bits of high current outputs

Abaco VME-2170A Digital Output - 32-bit optically isolated

  • On-board DIP switches provide 14-bit board address selection
  • Double Eurocard format with front panel
  • 8- or 16-bit data transfers
  • High isolated potential; 1 kV sustained, 6 kV pulsed
  • Positive or negative true options
  • High output voltage tolerance to 30 V normal mode
  • Open collector style output
  • Current source or sink output capability with low current option
  • Field configurable pull-up resistors
  • Externally supplied pull-up voltage for maximum isolation
  • 2.5 or 300 mA outputs
  • 32 optically isolated outputs

Abaco VME-2210 64-Channel Latching or Momentary Relay Board with Built-in-Test

  • Latching contacts will hold their state with power off
  • Available in latching and nonlatching versions
  • 1 Form C contacts (SPDT) with 96-conductor cable
  • 1 Form A contacts (SPST) with 64-conductor cable
  • 8-, 16-, 32-bit data transfers
  • Supports real time and offline fault detection and isolation
  • 2.0A current ratting
  • Protection from relays changing during power up/down

Abaco VME-2232A Relay Output Board 32-channel Relay with Built-in-Test (BIT)

  • 32 relay output channels (one form C relay per channel)
  • Contact ratings
    • 60W, 50 VA maximum switching power
    • 220 VDC, 250 VAC maximum switching voltage
    • 2A maximum switching current
    • 3A maximum carry current
  • Optional contact protection electronics for DC operation
  • 8-, 16-, or 32-bit data transfers
  • Built-in-Test (all active components are tested)
  • Front panel with fail LED
  • Compatible with the Intelligent I/O Controllers
  • VxWorks driver available
  • Software compatible with the VMIVME-2532 and the VMIVME-2533

Abaco VME-2510B 64-bit TTL Digital I/O with Built-in-Test (BIT)

  • 8-, 16-, 32-bit transfers
  • Optional open-collector outputs
  • High reliability DIN-type I/O connections
  • Built-in-Test logic for fault detection and isolation
  • Fail LED
  • Compatible with the Intelligent I/O Controller product line
  • Separate board address decoding for control and data registers
  • The direction of each 8-bit port is individually programmable
  • 64 mA sink capability

Abaco VME-2528 128-bit TTL Digital Input/Output Board

  • Alternating grounds on I/O pins
  • Real time loopback
  • Positive or negative true data I/O option
  • Nonprivileged or supervisory short I/O transfers
  • 8- or 16-bit transfers
  • Double Eurocard form factor
  • 24 mA output current sink capability
  • Individual port direction control jumpers
  • 128 bits of TTL compatible I/O

Abaco VME-2532A 32-bit High-Voltage Digital Input/Output Board

  • Optional output test jumpers for 100 percent testing of output drivers
  • Front panel with fail LED
  • Built-in-Test (off-line and real-time support)
  • 32 bits of high-voltage inputs
  • 8- or 16-bit data transfers
  • 32 bits of high-voltage outputs
  • Compatible with VMIC’s family of intelligent I/O controllers
  • Power up replacement

Abaco VME-2533 32-bit Differential Digital Output Board

  • Software compatible with VMIVME-2532
  • Powerup replacement option
  • Compatible with Intelligent I/O Controllers
  • Built-in-Test (all active components are tested)
  • Front panel with fail LED
  • 8-, 16-, or 32-bit transfers
  • Each data bit in each 16-bit data word represents one discrete line pair
  • RS-422/RS-485 compatible drivers and receivers
  • 32 bits of differential voltage outputs

Abaco VME-2534 32-bit High-Voltage Digital Input and/or Output Board with P2 I/O and Built-in-Test

  • Front panel with fail LED
  • 100 percent testing of all active components (including output drivers)
  • Built-in-Test (off-line and real-time support)
  • 32 bits of high-voltage inputs
  • P2 I/O connection (no front panel connectors)
  • 32 bits of high-voltage outputs

Abaco VME-2536 32-Channel Optically Coupled Digital I/O Board with Built-in-Test

  • 32 optically coupled outputs
  • 32 optically coupled inputs
  • High isolation potential
    • 1 kV sustained
    • 35 kV pulsed
  • 8-, 16, 32-bit data transfers
  • Standard data or short I/O addressing A16 or A24
  • Voltage sensing or contact sensing inputs
  • Input ranges of 5 to 125 VDC
  • 300 mA current sinking outputs
  • 50 V maximum output voltage
  • Supports Built-in-Test for both inputs and outputs

Abaco VME-2540 Intelligent Counter/Controller 24-channel slave I/O module

  • RS-422 differential interface with support for single-ended TTL inputs
  • Options allow configurations of 4, 8, 16, and 24 interfaces
  • On-board 15 MHz 68HC000 CPU
  • A32/A24/D32/D16/D8 (EO) VME slave interface, 64 Kbyte VMEbus memory window
  • Timer/periodic VMEbus interrupter - 0.0076 to 1,000 Hz
  • Quadrature position measurement - sin/cos up to 1 MHz, 32-bit counters, limit/modulo checking Integer period/pulse-width measurement 16- and 32-bit, discrete or continuous; low data transport lags
  • Square wave/pulse train generation - 0.0076 Hz to 2.5 MHz
  • Period/pulse-width measurement 400 ns to 8.5899 x 106s (32-bit floating point), 400 ns to 858s (32-bit unsigned integer)
  • Event counting - up to 4 giga events
  • Frequency measurement 1.16 x 10-3 Hz to 2.5 MHz

Abaco VME-3113B Scanning 12-bit Analog-to-Digital Converter with Built-in-Test

  • 64 differential or single-ended inputs
  • Powers up in autoscanning mode - no software initialization required
  • Continually digitizes input channels and stores the result in a dedicated channel dual-port register (autoscanning mode)
  • Jumper-selectable scanning of 2 to 64 channels
  • Supports real-time and off-line Built-In-Test
  • Five operating modes plus test mode
  • VMEbus interrupts may be programmed to interrupt upon completion of a single A/D conversion or upon completion of a 2- through 64-channel scan
  • User programmable interval timer supports scanning of all channels at periodic intervals
  • Jumper-programmable gain 1, 10, 100, 200 and 500
  • Selectable A/D ranges of 0 to +10V, ±5 V and ±10 V
  • Low-level and high-level inputs: ±10 mV to ±10 V
  • Optional low pass filter (the VME-3113B*) has improved high-frequency rejection characteristics
  • Overvoltage protected inputs
  • 5 x 10Ω input impedance
  • 33 kHz conversion rate
  • Selectable output code: offset binary, two's complement with sign extension

Abaco VME-6500 6U VME Multifunction I/O Board Analog and digital input/output

  • 64 K word memory
  • 6U form factor VME card
  • Access modes - all as per VITA 64 X standard
  • Self-calibration and Built-in-Test (BIT)
  • 1,000 V peak field to VME Bus isolation
  • RoHS, CE, UL 60950 compliant
  • Sheilded I/O connectors for EMI compliance
  • Compatible with Intelligent I/O Controller (IIOC)

Acromag AcPC424 - Digital Input/Output Module Differential, TTL, Counter/Timer

  • 24 differential I/O, 16 TTL I/O
  • Four 16-bit counter/timer channels with six operating modes
The AcPC424 provides 24 differential input/outputs, 16 TTL input/output channels, and four 16-bit multifunction counter/timers.
The 16 TTL input/output channels can be programmed as inputs or as outputs on an individual channel basis. The 24 differential input/output channels are programmed as inputs or outputs on an 4-channel port basis. All input channels can be enabled for change of state, low, or high level transition interrupts.
This module saves money and CompactPCI slots by combining differential I/O, TTL I/O, and counter/timer functions on one card.

Acromag AcPC464 - Digital Input/Output and Counter/Timer

  • 64 digital input/output channels
  • 16-bit counter/timer channels with six operating modes
  • Change of state and level interrupts
The AcPC464 module provides 64 digital input/ output channels and four 16-bit multifunction counter/timers.
All 64 I/O channels, when set as inputs, support configuration for interrupts on either a change-of-state or on a high-to-low or low-to-high transition. A debounce timer is selectable to help filter out false transitions.
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
This module saves money and CompactPCI slots by combining digital I/O and counter/timer functions on a single card.

Pages