Products

Displaying 1 - 8 of 8

AMREL PLA Series Air-Cooled Programmable DC Electronic Loads

  • Closed-case Calibration
    • With the eLoad line, there’s no longer a need to send your electronic load back to the factory for calibration or remove dozens of screws to reach a potentiometer. Simply follow the AMREL calibration routine from the front panel and you should be back up and running in a very short period of time (some electronic test equipment needed). This will virtually eliminate downtime and eradicate the annual cost associated with shipping your eLoad back to the factory for calibration.
  • Individual FET Protection
    • To ensure the reliability of the PLA Series, AMREL’s design includes individual FET protection. A programmable electronic load may contain many FETs in parallel, which can create a cascading failure if one of them was to short out. AMREL’s eLoad programmable electronic load design isolates failures so other components will not be affected or stressed, increasing the system’s level of protection against catastrophic failure. With individual FET protection, the MTTR is reduced and the electronic load quickly returns to full operation.
  • Ultra-low Voltage Operation
    • The PLA design allows the programmable electronic load to operate at voltage levels approaching .1V. They will typically dissipate full rated current below 1% of their maximum rated voltage. For example, a 60V unit designed to dissipate1500A will allow the user to operate at .6V and still dissipate the full amount.

AMREL PLW Series Water-Cooled Programmable DC Electronic Loads

  • Closed-case Calibration
    • With the PLW eLoad line, there's no longer a need to send your electronic load back to the factory for calibration or to remove dozens of screws to reach a potentiometer. Simply follow the AMREL calibration routine from the front panel and you should be back up and running in a very short period of time (some electronic test equipment needed). This will virtually eliminate downtime and eradicate the annual cost associated with shipping your eLoad back to the factory for calibration.
  • Individual FET Protection
    • To ensure the reliability of the PLW Series, AMREL's design includes individual FET protection. A programmable electronic load may contain many FETs in parallel, which can create a cascading failure if one of them was to short out. AMREL's eLoad programmable electronic load design isolates failures so other components will not be affected or stressed, increasing the system's level of protection against catastrophic failure. With individual FET protection, the MTTR is reduced and the electronic load quickly returns to full operation.
  • Ultra-low Voltage Operation
    • The PLW design allows the programmable electronic load to operate at voltage levels approaching .1V. They will typically dissipate full rated current below 1% of their maximum rated voltage. For example, a 60V unit designed to dissipate 1500A will allow the user to operate at .6V and still dissipate the full amount.

NH Research 4312 Series Modular DC Load 120V

  • 3 sizes – 150, 300, & 600W @ 120V with advanced measurement capability built-in
  • Mix & match loads for maximum configuration flexibility
  • Up to 16 loads in a single, 8 3/4″ / 5U Model 4300 chassis
  • Front loaded & front connections
  • 3 voltage and 3 current ranges for improved accuracy
  • High-resolution waveform capture for analysis of dynamic transients
  • Isolated digital inputs & outputs for test fixture support
  • PC/LAN control with LabVIEW & IVI drivers

NH Research 4350 Series Modular Programmable DC Electronic Load

  • 3 sizes – 150, 300, & 600W @ 500V with advanced measurement capability built-in
  • Mix & match loads for maximum configuration flexibility
  • Up to 16 loads in a single, 8 3/4″ / 5U Model 4300 chassis
  • Front loaded & front connections
  • 3 voltage and 3 current ranges for improved accuracy
  • High-resolution waveform capture for analysis of dynamic transients
  • Isolated digital inputs & outputs for test fixture support
  • PC/LAN control with LabVIEW & IVI drivers

NH Research 4700 Series High-Current DC Loads

  • 8 sizes – 1 to 36kW @ 120 or 600V
  • High-resolution waveform capture for analysis of dynamic transients
  • 18 built-in, precision voltage, current, power and timing measurements that eliminate additional dedicated measurement instruments
  • Isolated digital inputs and outputs for test fixture support
  • PC/LAN control using LabVIEW & IVI drivers
  • Optional touch-panel user interface

NH Research 4760 Series High-Voltage DC Loads

  • 600V, 1kW / 50A to 36kW / 1800A DC Loads
  • 3 Voltage and 2 current ranges
  • High accuracy 1 kW low power range
  • Advanced built-in measurements
    • 100kSamp/s waveform capture
    • Overshoot / Undershoot
    • Rise-Time / Fall-Time / Settling-Time
  • Test fixture support
    • 4 digital outputs
    • 2 digital inputs
  • Complex load profile playback
  • Multiple hardware control options
    • Manual touch-panel user interface
    • emPower™ test executive
    • PC/LAN control using LabVIEW & IVI Drivers

NH Research 9430 Series Regenerative 4-Quadrant AC Load

  • 8 Sizes – 4 to 96kW
  • Single, Split or Three-Phase programmable
  • 10 to 350VAC
  • 30 to 880Hz
  • DC operation to 10 to 400VDC
  • Reactive power capability 2.6 x Real Power
  • Sink power regenerated back to facility with >90% efficiency
  • Power factor range: -1 to +1
  • Crest factor range: 1.414 to 4.000
  • High-resolution waveform digitizer
  • 9” Touch-Panel user interface
  • High power density/minimum rack space

Sorensen SL Series Single Input DC programmable Loads

  • Flexible Product Line
    • Low power DC modules
    • Low power AC / DC modules
    • High power DC modules
    • Stand along modules
  • Remote: GPIB, RS-232, Analog (DC only)
  • DC Modes: CC, CR, CV, CP
  • AC Modes: CR, CC with crest factor control
  • Dynamic mode with slew rate control
  • Flexible Data Feedback
  • Current monitor output (SLM DC only