Southwest Microwave - Vertical Launch Connectors
For microstrip or grounded coplanar waveguide (GCPW) designs, Southwest Microwave solderless vertical launch connectors provide optimal signal integrity and are reusable. Suitable for various board materials and thicknesses, the vertical launch connectors reduce footprint requirements without sacrificing performance, resulting in design and installation convenience.
Vertical Launch 1.0mm (W) Jack (Female) 2-Hole Bolt-on
|
Model Number |
Frequency (GHz) |
Data Sheet |
|---|---|---|
|
18, 27, 36, 40, 50, 67, 110 |
Vertical Launch 1.35mm Jack (Female) 2-Hole Bolt-on
|
Model Number |
Frequency (GHz) |
Data Sheet |
|---|---|---|
|
18, 27, 36, 40, 50, 67, 90 |
Vertical Launch 1.85mm (V) Jack (Female) 2-Hole Bolt-on
|
Model Number |
Frequency (GHz) |
Data Sheet |
|---|---|---|
|
18, 27, 36, 40, 50, 67 |
Vertical Launch 2.40mm Jack (Female) 2-Hole Bolt-on
|
Model Number |
Frequency (GHz) |
Data Sheet |
|---|---|---|
|
18, 27, 36, 40, 50 |
Vertical Launch 2.92mm (K) Jack (Female) 2-Hole Bolt-on
|
Model Number |
Frequency (GHz) |
Data Sheet |
|---|---|---|
|
18, 27, 36, 40 |
Vertical Launch Compression Mount Plate
More Product Information
Focus recommends TRL Calibration Kits for applications such as load pull & noise parameters. Due to high reflection and low loss, tuner S-parameter measurements represent a challenge for VNA’s, because of error term determination and coupler directivity. Long experience has taught us not to rely on other calibration techniques than TRL (Thru-Reflect-Line). The popular SOLT technique is conditionally useable, but not guaranteed, up to 4GHz. The much convenient ECal method has provided questionable and inconsistent results. Our Customers are advised to be very careful with VNA calibrations, because the whole measured data depends on that.
Because of this, and to save our customers time and doubt, Focus has developed and offers a set of precise and reliable TRL calibration kits from 0.03 to 110 GHz with the following connector types: 7/16, N, APC-7, 3.5mm, 2.9mm, 2.4mm, 1.85mm, WR-15, WR-10. Our calibration kits are compatible with all commercial network analyzers.
For more information on TRL Calibration Kits, please read the following paper on TRL Versus SOLT
-
Double Conversion, Vertical/Free Standing, Online UPS System with Power Factor Correction
Image optimization features:
-
Auto gain (manual gain control: 0 to 32 dB)
-
Auto exposure (manual exposure control: 10 µs to 26.8 s)
-
Auto white balance (GT3300C only)
-
Binning (horizontal and vertical)
-
Color correction, hue, saturation (GT3300C only)
-
Column defect masking
-
Decimation X/Y
-
Gamma correction
-
Three look-up tables (LUTs)
-
Region of interest (ROI), separate ROI for auto features
-
Reverse X/Y
Camera control features:
-
P-Iris and DC-Iris lens control
-
Event channel
-
Image chunk data
-
IEEE 1588 Precision Time Protocol (PTP)
-
RS232
-
Storable user sets
-
StreamBytesPerSecond (bandwidth control)
-
Stream hold
-
Sync out modes: Trigger ready, input, exposing, readout, imaging, strobe, GPO
-
Tap mode switchable in Vimba Viewer 2.0 or later (four-tap, one-tap)
-
Temperature monitoring (main board and sensor board)
-
Trigger over Ethernet (ToE) Action Commands
Southwest Microwave’s high performance End Launch connectors are designed to provide low VSWR, mode free wideband response to 110 GHz for single-layer and multi-layer printed circuit boards where the high frequency signal is on the top layer. Available in SMA (27 GHz), 2.92 mm (K) (40 GHz), 2.40 mm (50 GHz), 1.85 mm (V) (67 GHz) and 1.0 mm (W) (110 GHz).
Male and female options along with narrow body and bulkhead feed-through. Unique clamping mechanism accommodates board thickness up to .300” (7.62 mm). Robust, reusable and repairable. Multiple launch configurations provide the best possible match to circuit layout. Works on microstrip and grounded coplanar waveguide (GCPW) designs. Signal-layer microstrip and GCPW test boards available. Soldering is optional.
Design Assistance:
- Printed circuit board layout and connector part number recommendation
- 3D models for mechanical layout
- HFSS models (version 18.0 or newer) for EM simulations upon request and availability
-
Combine up to 12 fail-safe building blocks, dual SPDT, SP4T, SP6T, or transfer switch in a compact 1U footprint
-
Front “pluggable” relays facilitate field maintenance
-
Embedded web interface provides interactive utility to monitor and control relays from anywhere in the world
-
Flexible API supports IVI and Linux development environments minimizing software investment
-
LXI Trigger Event implementation provides seamless test synchronization with external devices
-
Store up to 128 relay state configurations for quick recall, including an automatic power up state
-
Define exclude lists to avoid setting an undesirable configuration
-
Relay odometer tracks closures to facilitate preventative maintenance
Image optimization features:
-
Auto gain (manual gain control: 0 to 32 dB)
-
Auto exposure (manual exposure control: 30 µs to 33.5 s)
-
Auto white balance (GT6600C model only)
-
Binning (horizontal and vertical)
-
Color correction, hue, saturation (GT6600C only)
-
Column defect masking
-
Decimation X/Y
-
Gamma correction
-
Three look-up tables (LUTs)
-
Region of interest (ROI), separate ROI for auto features
-
Reverse X/Y
Camera control features:
-
EF lens control (order option -18)
-
Event channel
-
Image chunk data
-
IEEE 1588 Precision Time Protocol (PTP)
-
RS232
-
Storable user sets
-
StreamBytesPerSecond (bandwidth control)
-
Stream hold
-
Sync out modes: Trigger ready, input, exposing, readout, imaging, strobe, GPO
-
Tap mode switchable in Vimba Viewer 2.0 or later (four-tap, one-tap)
-
Temperature monitoring (main board and sensor board)
-
Trigger over Ethernet (ToE) Action Commands
1.35 mm (E) DC to 90 GHz connectors from Southwest Microwave include a new Solderless Vertical launch connectors are designed for microstrip or grounded coplanar boards. They provide optimal signal integrity, are reusable and are installed without soldering. Suitable for various board materials and thickness.
Image optimization features:
-
Auto gain (manual gain control: 0 to 32 dB)
-
Auto exposure (manual exposure control: 10 µs to 26.8 s)
-
Auto white balance (GT2300C only)
-
Binning (horizontal and vertical)
-
Color correction, hue, saturation (GT2300C only)
-
Column defect masking
-
Decimation X/Y
-
Gamma correction
-
Three look-up tables (LUTs)
-
Region of interest (ROI), separate ROI for auto features
-
Reverse X/Y
Camera control features:
-
P-Iris and DC-Iris lens control
-
Event channel
-
Image chunk data
-
IEEE 1588 Precision Time Protocol (PTP)
-
RS232
-
Storable user sets
-
StreamBytesPerSecond (bandwidth control)
-
Stream hold
-
Sync out modes: Trigger ready, input, exposing, readout, imaging, strobe, GPO
-
Tap mode switchable in Vimba Viewer 2.0 or later (four-tap, one-tap)
-
Temperature monitoring (main board and sensor board)
-
Trigger over Ethernet (ToE) Action Commands
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range. Focus uses two basic technologies:
a) For frequencies from 100MHz to 110GHz (and above) we use the slide screw technique (models Multi Harmonic MPT, wideband (fundamental) CCMT, harmonic rejection PHT), in which a reflective probe (slug) is inserted into the slot of a low loss slotted transmission line (slabline or waveguide).
b) For frequencies from below 10MHz to 170MHz we use a lumped element technology (models LFT), whereby variable capacitors are connected with optimized lengths of coaxial cable.
Southwest Microwave
Since 1981, Southwest Microwave has delivered performance-leading interconnect solutions currently available from DC to 110 GHz for hi-rel/space, defense, instrumentation, integrated-circuit and PCB evaluation applications. Built in the USA to rigorous performance and quality standards, Southwest Microwave connectors deliver the industry’s lowest RF leakage, insertion loss and VSWR. Products include Super SMA, N, TNC, SSMA, 2.92mm, 2.40mm, 1.85mm, 1.35mm, 1.0mm and 0.9mm SuperMini connectors in a variety of mounting configurations, plus board-mount (end-launch, vertical launch, board-to-board) connectors, cable assemblies, coax contacts for multicavity connectors, adapters, installation tools and launch accessories for microstrip, stripline and coplanar launches.
Contact Details
Southwest Microwave - Corporate Headquarters
9055 S. McKemy St., Tempe, AZ 85284-2946, USA
Phone: 480-783-0201
Fax: 480-783-0360
Test & Measurement
Download Line Card
Document
Embedded
Download Line Card
Document
