Sorensen - SLM DC Single Input DC programmable Loads
-
Flexible Product Line
-
Low power DC modules
-
Low power AC modules
-
High power DC, 19" rack mounted loads
-
High power AC, 19" rack mounted loads
-
26 Total Models
-
-
Flexible Control
-
Remote: GPIB, RS-232, Analog
-
Manual: Front Panel
-
DC Modes: CC, CR, CV, CP
-
AC Modes: CR, CC with crest factor control
-
Dynamic mode with slew rate control
-
-
Flexible Data Feedback
-
GPIB, RS-232
-
Current monitor output (SLM DC only)
-
Front panel
-
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
The SLM family includes 11 models of fully programmable, single input AC or DC modular electronic loads. DC models are offered to test power supplies, battery chargers, battery discharge, power supply transient response and integration into ATE systems. AC models are ideal to test low power inverters.
The DC models support operation in Constant Current, Constant Voltage, Constant Resistance or Constant Power mode as well as a short simulation. Engineers have ultimate control of current waveforms by using either the analog input or CC dynamic mode. An analog input (single input DC models) allows arbitrary current waveforms up to 20kHz with an external 0-10V signal. In dynamic mode, the pulse generator allows fast state switching between two programmed current levels with programmed slew rate and dwell times.
More Product Information
-
Direct PC bus access data acquisition system provides the required sampling rate and resolution to meet IEC 61000-4-7 measurement requirements and supports high speed data transfers, unlike competing IEC test systems which provide only limited throughput using IEEE-488.
-
PC based Harmonic and Flicker test software provides real-time full color data display updates and continuous PASS/FAIL monitoring.
-
Automatic calculation of the maximum permissible system impedance Zsys, using the Zref and measured Flicker parameters, as required per EN/IEC 61000-3-11.
-
Simple user operation under Windows provides IEC test setup, data analysis, display and MS Word test reports.
-
High resolution, no gap acquisition data storage to ensure that all data can be streamed to disk (in ASCII format if needed) for later review and replay of actual test.
-
Single Step and Fast playback mode of test results
-
Precise programming of voltage and current slew rate for sensitive loads.
-
Industrial field bus interface (Modbus-TCP, Modbus-RTU, Ethernet) enable real-time digital control.
-
Built in power quality monitoring detects and saves input voltage anomalies which can be saved for later diagnostic analysis.
-
Programmable analog interface scaling facilitates integrating the ASD FLX with existing systems easily.
-
Built-in energy meter calculates the delivered energy throughout a process or period of time.
-
Optional real time clock enables accurate timestamping of events.
-
Single Package 6-Pack of 600W power supplies
-
Complete self-contained controller operates independently once pre-set
-
Capable of ramps and sequences
-
Capable of inter-channel dependent operation
-
DeviceNet Interface
-
Solid State polarity switching
-
Different substrate carriers for wafers up to 200 mm or single dies
-
Probe cards and/or up to eight positioners
-
Probe positioners placed inside vacuum chamber
-
Short and stable probe arms
-
Intuitive, manual drives
-
Front loading capability through load door
-
Software control of chuck for fast step-and-repeat testing of the entire wafer
-
Fast step-and-repeat testing of the whole wafer
-
CMOSIS/ams CMV4000 sensor
-
Power over Ethernet option
-
Angled-head and board level variants
-
Video-iris lens control
-
Monochrome (G-419B) and color (G-419C) models
-
GigE Vision interface with Power over Ethernet option
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads on top and bottom of housing or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Defect pixel masking feature with the Defect Mask Loader tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Comprehensive I/O functionality for simplified system integration
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system cost
-
IEEE 1588 Precision Time Protocol allows for easy synchronization of multiple cameras and devices on network
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads on top and bottom of housing or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba SDK and compatibility to the most popular third party image-processing libraries.
-
Defect pixel masking feature with the Defect Mask Loader tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
Select between B 270 ASG protection glass and filter types: Jenofilt 217 IR cut filter, Hoya C-5000 IR cut filter, RG715 IR pass filter, or RG830 IR pass filter
-
Versatile temperature range for extreme environments
-
IEEE 1588 PTP
-
Power over Ethernet
-
P-Iris and DC-Iris lens control
-
Monochrome (GT1380) and color (GT1380C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
- Support the most high-performance Camera Link cameras with available support for Full and 80-bit mode at up to 85 MHz
- Perform deterministic image acquisition by way of the jitter-free Camera Link 2.1 interface
- Maximize system compatibility with the choice of PCIe® 2.1 x1, x4 or x8 connectivity
- Eliminate missed frames with ample onboard buffering and PCIe bandwidth
- Optimize multi-camera applications via support for up to four Base or two Full/80-bit Camera Link cameras per board
- Minimize space requirements and maximize PC compatibility through a half-length design with mini Camera Link connectivity for true single-slot operation
- Improve and simplify system connectivity with Power-overCamera-Link (PoCL) support at extended cable lengths
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries