• Compliant with IEC 61000-4-5 Ed.3 standard：ECE R10 is regulated at Ed.2, possible to switch to Ed.2
• AC500V/200A DC600V/200A built-in coupling decoupling network.
• Built-in EV relay welding protection diode in DC line. You can evaluate the lightning surge resistance when charging EV / PHV vehicles, which is required by ECE R10-04 / 05. (EV Fast Charging applicable)
• Maximum output voltage 15kV: In the reliability evaluation test of the lightning surge test, the evaluation including the destructive test can be performed.
• Adopt a large LCD screen operation panel: A large LCD panel screen has been adopted for the operation unit to improve visibility and operability.
• Employs MPU control that simplifies continuous testing: Surge output / waveform switching / polarity switching / sequence operation can be performed automatically.
• Equipped with manual and program modes. Manual mode for standard tests and single condition tests, and Program mode for continuous tests under different conditions. You can easily set test conditions according to your application.
• Excellent safety functions including interlock
• Equipped with waveform check terminal as standard
• You can check the output waveform with your oscilloscope and BNC cable.
• Isolation transformer required to protect the power supply for EUT is available. (option)
• Possible to switch the constant of the decoupling circuit in order to prevent resonance with the power supply.
• Possible to switch to a circuit not including 18uF in the surge output of IEC61000-4-5 Edition 2.0 2005 version).

* This product is a custom product. Please contact us for details.

Customization up to DC1000V is available.

The VTI Instruments 16-Channel isolated high voltage measurement instrument

• 24-bit SAR ADC per Channel
• 128k samples/second/channel sample rate
• 1000V channel-channel isolation
• 500V channel-ground isolation
• Input voltage ranges peak: ±420V/±10V/±1V
• Data logger acquisition mode
• 3-Pin screw terminal input connector
• LXI ethernet interface
• IEEE-1588 synchronization
• Power over Ethernet (PoE+) or 12– 50 V DC input
• Simultaneous data streaming
• 8-bit bank isolated digital I/O
• Full-featured embedded web interface
• Compact 1U half-rack form factor

Parts in compliance with all SMOT document requirements.

• On-Off power switch
• 20 A Circuit Breaker
• 8’ Flexible Power Cord
• Outlets – (4) 5-20R

• 3ft.
• (2) fork terminals (current)
• (1) fork terminals (ground)
• (2) Shielded Banana (voltage)

• Simplify cabling between cameras and vision computer through PoE support 
• Facilitate multi-camera configurations with two or four Gigabit Ethernet ports 
• Trigger multiple cameras simultaneously and reliably using hardware-assisted trigger-over-Ethernet (ToE) 
• Synchronize to automation devices in real-time through digital I/Os with hardware-assisted management 
• Deploy pre-licensed for GigE Vision support in Aurora software, formerly Matrox Imaging Software 
• Avoid the need for a separate hardware key through a license fingerprint for additional Aurora software features 
• Certified for use with GigE Vision systems

• IEC 61000-4-4 Ed.3 standard compliance. 
• Pre-check function is installed. Inspection before testing is now easy. 
• Normal mode test support. Taking account of field troubles is possible. (option) 
• Utilize an outlet box that simplifies EUT connection. (option) 
• Compared with conventional products, the size has become compact. (Approximately 67% by volume) 
• Easy to understand Panel display reduces mistakes in connecting power cables. 
• Software control with Windows. (option) 
• Next calibration date can be notified. (Windows software only) 
• Employ LCD screen with multi-language support and enhanced operability. 
• Maximum output voltage of 5 kV and maximum pulse frequency of 2 MHz allow you to test above the standard test level. 
• CDN capacity is increased to single phase type AC 240 V 20 A, single and three phase type to AC 600 V 63 A, supporting wider range of EUT. 
• Large capacity CDN (100 A or 150 A) option available for Injection test on various EUT. 
• Using coupling clamps, EMS probe kits, you can test the signal lines and evaluate the noise immunity on the PCB. (option)

LUMIMAX® High Power LED Spot Lights are particularly compact, but at the same time extremely powerful and versatile. 

Adjustable precision optics of the LED Spot Lights allow adjustment of the radiation characteristic to the required working distances and image fields, enabling a focused or very homogeneous illumination of the object to be inspected.

LED Spot Light's filter thread allows mounting of components such as polarisation filters or bandpass filters for fluorescence applications. With the C-Mount connector, either integrated or available as an accessory, lenses for focusing can be used.

Despite their compact design, the LUMIMAX® LED Spot Lights feature an integrated lighting controller for continuous or strobe mode.

Our patented miniaturized L/S/C Tri-Band Feed delivers top-notch performance and unmatched flexibility.

Equipped with a common L/S/C radiating front end, it’s complemented by a modular set of active RF modules, enabling simultaneous reception and tracking across various frequency bands. Its compact, lightweight design allows it to be mounted on any dishes ranging from 6 to 24 feet.

Available in single, dual, or tri-band configurations, this feed offers the best value for customers looking to meet current requirements while staying future-ready.

It’s also field-upgradable to add any missing bands with straightforward RF module additions, ensuring scalability while keeping costs in check.