Product Finder

Displaying 1 - 5 of 5
Product Results:
Elgar - Battery String Simulator (BSS)

Elgar - Battery String Simulator (BSS)

Available in single and dual pack versions Sensor simulation available to provide thermistor, strain gauges, heater loads, and cell bypass/short...
NH Research - 9200 Series Battery Emulator - Modular, Regenerative Battery Pack Emulator with Power Range from 12kW up to 21 Channels

NH Research - 9200 Series Battery Emulator - Modular, Regenerative Battery Pack Emulator with Power Range from 12kW up to 21 Channels

High configuration flexibility Bi-directional DC Source, expandable from 12 to 252kW with 40, 120 or 600V Regenerative, greater than 90%...
NH Research - 9210 Series Single Channel Battery Test System

NH Research - 9210 Series Single Channel Battery Test System

Smaller footprint makes it easier to move within a lab (roughly half the size of the 9200) Custom waveform/profile generation Sub-mS voltage,...
NH Research - 9220 Series Low Voltage/High Current Battery Charge/Discharge Test System - Regenerative Battery Cycler, Power Cycling, & Life-Cycle Testing of Low Voltage/High Current Batteries

NH Research - 9220 Series Low Voltage/High Current Battery Charge/Discharge Test System - Regenerative Battery Cycler, Power Cycling, & Life-Cycle Testing of Low Voltage/High Current Batteries

Single output up to 40V/3,600A/72kW per system Parallel expansion up to 7,200A Built-in digital measurements including Ah & kWh...
NH Research - 9300 Series High-Voltage Battery Test System - Modular, Regenerative Battery Test System with Power Range from 100kW up to 2.4MW

NH Research - 9300 Series High-Voltage Battery Test System - Modular, Regenerative Battery Test System with Power Range from 100kW up to 2.4MW

Wide Operating Envelope at 100kW per cabinet Scalable to 1.2MW/4000A Regenerative, greater than 90% efficiency of discharge power returned to AC...

  • Do more with the same air compressors–delay the capital expense of installing an additional compressor
  • Ensure proper air pressure to your pneumatic equipment
  • Lower energy costs
  • Reduce leak detection time
  • Improve reliability in your production line
  • Make leak detection part of your typical maintenance routine
  • Train the team in a matter of minutes
  • Validate repairs on the spot


  • Enabled with current and voltage measurement functions, in a compact size
  • Measures resistance & continuity to check for broken wires
  • Data hold & backlit display to keep you working safe and fast


  • Power quality statistics according to EN50160
  • Voltage event list (dips, swells and interruptions)
  • Continuous recording of:
    • Voltage
    • Current
    • Power P, Q, S
    • Power factor
    • kWh
    • Flicker
    • Unbalance
    • Frequency
    • Voltage and current harmonics to the 50th / Interharmonics
    • THD
    • Mains signaling
  • Triggered recordings
  • Online mode (Oscilloscope, transients and events)
  • Fast transient analysis up to 10 MHz
  • 4, 600 V voltage probes
  • 4 dual-range flexible current probes (1000 A / 200 A AC)
  • GPS time sync receiver
  • 2 GB Flash Memory


  • Measure up to 1000 V AC and DC
  • Measure up to 10 A (20 A for 30 seconds)
  • 10,000 μF capacitance range
  • Frequency to 200 kHz
  • Extended AC voltage bandwidth – 40 Hz to 30 kHz
  • Resistance, continuity and diode test
  • Min/Max and average recording to capture variations automatically


  • 0.1% DC accuracy
  • Current measurements up to 10 A, 20 A for up to 30 seconds
  • Millisecond pulse width measurements for fuel injectors
  • Optional magnetic hanger allows meter to attach to the vehicle and free your hands for other tasks
  • Min/Max/Average recording with Min/Max Alert to capture variations automatically
  • Peak Min/Max to record transients as fast as 250 μs
  • Relative mode to remove test lead resistance from low ohms measurements
  • Auto and manual ranging for maximum flexibility
  • Autohold™ to capture stable readings with only one touch of the leads
  • Large display digits and two-level bright white backlight for increased visibility
  • Analog bargraph to track changing or unstable signals
  • Input Alert provides audible warning against wrong use of input jacks
  • Access door for fast battery changes without opening up the case
  • "Classic" design that fits your hand with new removable holster, built-in test lead and probe storage
  • 10 meg ohm input impedance won’t damage computer circuits
  • Limited lifetime warranty