VTI Instruments - EX1200 Series Digital I/O (EX1200-7500)
-
The EX1200-7500 is a 64 -Channel, 2 MHz, Digital I/O with Eight ports of 8 I/O bits each
- Eight ports of 8 I/O bits each
- High current capability for control of external relays, 300 mA sink
- Simulate and receive digital data at up to 2 MHz sample rates
- Selectable output voltages range from 3.3 V to 60 V
- Setup outputs and scan inputs as part of EX1200 measurement sequencing engine
The EX1200-7500 is a high-performance I/O module with eight 8-bit ports (64 channels). Each port may be configured as an input or output under program control. The I/O may be single buffered, to provide real time data access, or double buffered, to provide synchronized data.
The EX1200-7500 has the flexibility to source the input and output clocks from the front panel allowing very large numbers of channels to be synchronized to collect or present data to a UUT. Additionally, input data can be timestamped to IEEE-1588 precision as part of the EX1200 scan engine. Deep on board memory (up to 1 MB) can be used to generate patterns on output channels at rates up to 2 MHz. In order to ease overall system cabling, all clamping diodes and open collector channels can be pulled up internally, rather than on a per channel basis.
Each channel can sink 300 mA, and includes built-in clamping diodes making this module ideal for driving and sensing external devices such as relays.
More Product Information
-
Provides an effectively noise free environment around the device under test (DUT)
-
World’s first probe station with integrated TestCell Power Management (a TestCell is a connected set of equipment, including test software, instruments, probe station, thermal system, and related measurement accessories such as cables and on-wafer probes)
-
Up to 4x faster flicker noise thermal testing on 30 μm pads
-
Provides dark and dry environment for measuring light sensitive transistors, and devices at negative temperatures (<= -60°C) with frost free operation
-
Provides fully managed and filtered AC power to the entire system – prober and instruments
-
Filters harmful noise generated by external thermal control systems
-
Reduced “antenna effect” injection of unwanted RF noise into the measurement path
-
Provide up to 100dB attenuation (50Hz to 80Mhz) with 100mA max DC current handling
-
Ultra-low, fA-level current and fF-level capacitance measurements from -65 °C to + 300 °C
-
Enables full access to the chuck and the auxiliary sites
-
Intuitive, and precise movement of chuck in X, Y, and Z-direction
-
User-centered design minimizes training costs and enhances efficiency
-
Test automation out-of-cassette for higher test cell efficiency for over-night/over-weekend operation
-
Combine up to 16 SPDT or 8 multiport, high-performance relays in a 2U footprint
-
Latching/Terminated options (EX7204L)
-
LXI/LAN and USB command and control options
-
Embedded web interface provides interactive utility to monitor and control relays from anywhere in the world
-
Flexible API supports IVI and Linux development environments minimizing software investment
-
LXI trigger event implementation provides seamless test synchronization with external devices
-
Store up to 128 relay configurations for quick recall, including automatic power-up state
-
Intuitive, icon-based setup and control
-
Spreadsheet-style channel configuration
-
Snapshot display with data export
-
Independent sampling rates for each instrument
-
Real-time online graphical data analysis
-
Client / server architecture with multiple displays
-
Synchronization of different data sources
-
Detect/process events for close-loop control
-
Post-acquisition analysis methods and data playback
-
Easily create Virtual/Calculated channels based on physical channel data
-
Direct PC bus access data acquisition system provides the required sampling rate and resolution to meet IEC 61000-4-7 measurement requirements and supports high speed data transfers, unlike competing IEC test systems which provide only limited throughput using IEEE-488.
-
PC based Harmonic and Flicker test software provides real-time full color data display updates and continuous PASS/FAIL monitoring.
-
Automatic calculation of the maximum permissible system impedance Zsys, using the Zref and measured Flicker parameters, as required per EN/IEC 61000-3-11.
-
Simple user operation under Windows provides IEC test setup, data analysis, display and MS Word test reports.
-
High resolution, no gap acquisition data storage to ensure that all data can be streamed to disk (in ASCII format if needed) for later review and replay of actual test.
-
Single Step and Fast playback mode of test results
-
16 integrated analog backplane lines
-
4-slot carrier plugs into a standard EX1208A series mainframe
-
Configure with either Resource or I/O matrix modules in any combination
-
1 or 2 pole switching options, up to 300 V/2 A
-
Typical bandwidths in excess of 20 MHz
-
Integrate with optional 6.5 Digit DMM across backplane
-
Up to 176 x 8 2-wire configuration in 4-slots, 704 x 8 in a single 3u mainframe
-
Pre-program hardware triggers to automate relay states and reduce cycle time
-
Eight ports of 8 I/O bits each
-
High current capability for control of external relays, 300 mA sink
-
Simulate and receive digital data at up to 2 MHz sample rates
-
Selectable output voltages range from 3.3 V to 60 V
-
Setup outputs and scan inputs as part of EX1200 measurement sequencing engine
-
Autonomous Modal Parameter Estimation Procedure
-
Multiple Live Parameter Estimation Windows
-
Task Oriented, Easy-To-Use Interface
-
Logical Operation Always "One-Click" away
-
Simplified "Copy & Paste" Data Management
-
Simplified Units Unification Tool
-
Based on MATLAB® Computational Engine Environment
-
Universal File Format (UFF) Data Access
-
Individual Data Channel Calibration
-
The EX1200-7500 is a 64 -Channel, 2 MHz, Digital I/O with Eight ports of 8 I/O bits each
VTI Instruments
VTI Instruments, an AMETEK Programmable Power brand, provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time. A sustained focus on innovation and technology enables customers to optimize their capital investment through product longevity, while ensuring unmatched measurement integrity and data reliability.
VTI Instruments has customers in over 30 different countries and in a wide variety of industries including aerospace, defense, power generation, automotive and consumer electronics.
Contact Details
AMETEK Programmable Power, Inc. (VTI Instruments) − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries