Product Finder

Displaying 1 - 3 of 3
Product Results:
SunAR RF Motion - TLT2 - Bore-Sight Antenna Positioning Tower

SunAR RF Motion - TLT2 - Bore-Sight Antenna Positioning Tower

New trolley guide concept enhances azimuthal stability Dual load carriers give rigid, stable elevation under heaviest loads Stable boom extension...
SunAR RF Motion - TLT3 - Bore-Sight Antenna Positioning Tower

SunAR RF Motion - TLT3 - Bore-Sight Antenna Positioning Tower

EUT distance: 1 m (worst case) Calibration point height: 4 m Tower height: 15’3” Taller towers for larger antennas...
SunAR RF Motion - TWR99, TWR95 - Motorized Antenna Positioning Towers Standard/Compact Antenna Towers

SunAR RF Motion - TWR99, TWR95 - Motorized Antenna Positioning Towers Standard/Compact Antenna Towers

1-2.5 meter (TWR99) and 1-4 meter (TWR95) antenna height standard, 1-6 meter optional Electric height adjustment 1 cm height resolution, 0.1m/sec...

  • Optional magnetic hanger for easy set-up and viewing while freeing your hands for other tasks
  • Large digit display with bright, two-level backlight makes the 83V significantly easier to read than older models
  • 6000 counts, 3-3/4 digits
  • Measure up to 1000 V AC and DC
  • Measure up to 10 A, 20 A for up to 30 seconds
  • Frequency to 200 kHz and % duty cycle
  • Resistance, continuity and diode test
  • 10,000 µF capacitance range for components and motor caps
  • Min/Max-Average recording with Min/Max Alert to capture variations automatically
  • Relative mode to remove test lead interference from low ohms measurements
  • Auto and manual ranging for maximum flexibility
  • Touch Hold to capture stable readings avoiding noisy signals
  • Large display digits and two-level bright white backlight for increased visibility
  • Analog bargraph for fast changing or unstable signals
  • Input Alert provides audible warning against wrong use of input jacks
  • Improved selectable sleep mode for long battery life
  • Access door for fast battery changes without breaking the calibration seal
  • "Classic" design with new removable holster with built in test lead and probe storage
  • Lifetime warranty
Electrical safety
All inputs are updated to the 3rd edition of ANSI/ISA S82.01 and EN61010-1 CAT IV 600 V and CAT III, 1000 V. They can withstand impulses in excess of 8.000 V and reduce risks related to surges and spikes.
  • Measure AC current with an optional current clamp accessory


  • A completely sealed, IP67 rated case
  • Withstands drops up to 10 ft or 3 m (with holster)
  • Dustproof per IEC 60529 IP6x
  • Waterproof per IEC 60529 IPx7
  • CAT III 1000 V, CAT IV 600 V
  • Reversible holster for added protection of the display when not in use


  • Measure up to 1000 V AC and DC
  • Measure up to 10 A (20 A for 30 seconds)
  • 10,000 μF capacitance range
  • Frequency to 200 kHz
  • Extended AC voltage bandwidth – 40 Hz to 30 kHz
  • Resistance, continuity and diode test
  • Min/Max and average recording to capture variations automatically


  • Contact and non-contact IR thermometer for measuring up close or at a distance, without a ladder
  • Measures temperature from -40°C to 550° C (-40°F to 1022°F)
  • Works with all standard mini-connector type K thermocouples
  • Provides single-point laser sighting
  • Allows easy emissivity adjustment for measuring pipes and other shiny surfaces more accurately


  • Power quality statistics according to EN50160
  • Voltage event list (dips, swells and interruptions)
  • Continuous recording of:
    • Voltage
    • Current
    • Power P, Q, S
    • Power factor
    • kWh
    • Flicker
    • Unbalance
    • Frequency
    • Voltage and current harmonics to the 50th / Interharmonics
    • THD
    • Mains signaling
  • Triggered recordings
  • Online mode (Oscilloscope, transients and events)
  • Fast transient analysis up to 10 MHz
  • 4, 600 V voltage probes
  • 4 dual-range flexible current probes (1000 A / 200 A AC)
  • GPS time sync receiver
  • 2 GB Flash Memory