eZ Viewer is a data post-flight replay software for use with mission data based on IRIG-106 Chapter 10 format, recorded on ENERTEC recorder/server. This software is an easy-to-use, quick setup and intuitive tool targeted for data replay.

Key Features Comprehensive software tool for:

• Configuration of mission debriefing post-flight debriefing / mission analysis
• Data from on the media or archived

Intuitive interface:

• Pre-configuration of display
• Easy to use and quick setup
• SQUADRON mode

• Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope 
• Automatic probe detection 
• Provides all necessary power and offset control to the attached probe 
• Supports probes up to 4 GHz 
• Easy firmware updates 
• Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes

Differential active probes are like two probes in one. Instead of measuring a test point in relation to a ground point (like single-ended active probes), differential probes measure the difference in voltage of a test point in relation to another test point

• All-in-One Support for RF Measurements and Protocol Tests in FR1 (to 7.125 GHz) and FR2 (Millimeter Wave) Bands
• Supports mm-wave band RF measurements and beam forming tests combined use with the RF chamber.
• Flexible Platform using Modular Architecture
• Supports Existing LTE Test Environment
• Supports various functional tests by GUI operation only without requiring difficult scenario development
• Measures maximum IP data throughput for wide variety of band, CA, and MIMO combinations 

Note: The design, explanation and appearance are subject to change without notice.

• Spin mode is a dynamic mode intended to provide a simulation of a spinning satellite. 
• Enhanced Eclipse mode is a dynamic mode that allows the user to easily program and initiate an eclipse event with total control over all of the V-I curve parameters and dwell times. 
• Operates with Sequential Shunt Regulators and Maximum Power Point Trackers 
• Multiple redundant OVP/OIP layers

Enhance the reliability of your test data with EagleLink, designed specifically for aircraft and UAVs. EagleLink is crucial for preventing data loss that can delay missions and increase costs, making a dependable transmitter essential.

EagleLink exemplifies technological excellence, tailored for the stringent demands of aviation operations. Its cutting-edge SDR (Software-Defined Radio) architecture and SoC (System on Chip) integration offer superior adaptability for modulation and data preprocessing, ensuring readiness for future advancements.

The integration process is simple and efficient, facilitating quick deployment. EagleLink is compatible with standard PCM inputs or Ethernet for telemetry, adhering to IRIG-106 Chapter 7-2015 standards.

Opt for EagleLink for secure, reliable mission support and optimized resource management.

• LMR Signal Analyzers with Coverage Mapping: P25, P25 Phase 2, DMR (MotoTRBO™), TETRA, NXDN, dPMR, PTC-ITCR, PTC-ACSES, NBFM, FDD & TDD LTE
• Broadband Signal Analyzers: LTE, WiMAX
• Interference Analyzer with Interference Mapping and support for MA2700A Handheld Interference Hunter
• Auto Test and Alignment of Motorola APX P25 mobiles and portables
• Direct measurement of up to 150 watt transmitters
• Spectrum Analyzer: 9 kHz – 1.6 GHz, optional to 6 GHz
• Cable and Antenna Analyzer: 500 kHz – 1.6 GHz, optional to 6 GHz
• Return Loss, VSWR, Insertion Loss, S11 / S21, DTF
• PIM Hunting
• Internal Power Meter, optional External Power Sensor
• Handheld, battery-operated design
• Weighs less than 7.6 lb (including battery)
• Rugged, field-proven design using Anritsu's 9th generation hardware platform
• Daylight viewable color touchscreen display
• Superior Immunity to RF interference
• Remote control via Ethernet
• Standard three-year warranty (battery one-year warranty)