• 6 GHz, 8 GHz, 18 GHz and 40 GHz RF Power Sensors
• Up to 195 MHz video bandwidth with 3 ns rise time
• Real-Time Power ProcessingTM technology with zero measurement dead time
• 100,000 measurements per second
• Power Analyzer Suite advanced measurement and analysis software
• Crest factor, CCDF and statistical measurements
• 10 GS/s effective sample rate
• 100 MS/s continuous sample rate
• Synchronized multi-channel measurements

• S-parameters comparison of user-characterized and factory-characterized verification standards
• S-parameters comparison of user-characterized and factory-characterized verification standards with measurement uncertainty boundaries
• Includes beaded airline, mismatch airline, offset shorts and fixed loads

• High ENR
• Wide frequency range
• Custom frequencies available

The NC3600 Series coaxial noise sources are an excellent choice for applications requiring high ENR, such as ATE, radiometer, and radar systems.

An SMA male connector is standard for the RF output and feed thrus for bias input. SMA female is an option. Custom frequencies and flatness available. Contact the factory with your request.

The VectorStar ME7838x4 broadband system VNA offers the widest available 4-port single sweep measurements from 70 kHz to 110, 125, 145, and 150 GHz with mmWave bands up to 1.1 THz

• The ME7838E4X 4-port system sweeps from 70 kHz to 110 GHz (Guaranteed specifications)
• The ME7838A4X 4-port system sweeps from 70 kHz to 125 GHz (Guaranteed specifications)
• The ME7838D4 4-port system sweeps from 70 kHz to 145/150 GHz
• The ME7838G4 4-port system sweeps from 70 kHz to 220 GHz
• All systems may be configured to include banded millimeter-wave modules up to 1.1 THz
• Industry-best calibration and measurement stability: 0.1 dB vs 0.6 dB over 24 hrs
• All systems also supports the 3744x-Rx receiver for noise figure measurements to 125 GHz
• Compact, lightweight mmWave modules offer low cost installation with industry-best performance

• SPA available from 70KHz to 20/40/70/110/125/145 and 220GHz. Also available for banded configuration to 1.1THz.
• Dual SPA mode available: suitable for Mixers/Amplifier/ Harmonics /Spurious testing.
• SPA available on all ports. User can define which port to use as SPA port.
• Several detection types available in classical mode: Peak, minimum, RMS, Mean.
• Various math functions can be applied on SPA mode like Min hold/max hold/ user defined equations.
• Sources and receivers can be independently configured. Can be used as Tracking Generator.
• For units that have a dual source, a dual drive option is available. Support for external source control also possible.
• Phase synchronization for units with Dual source available. This feature allows users to control and configure the phase between the two sources.
• Source and receiver attenuator available with VNA can be activated in SPA mode. Recommendation to use option 62 (with attenuator on receiver side) for measuring the spectrum content of high-power devices.
• Software option: easy to install and upgrade existing user equipment.

• Excellent temperature and voltage stability
• Units for noise figure meters feature 15.5-dB ± 0.75 dB ENR output
• High-output units for radar and satellite communications system testing feature output between 26 and 35 dB ± 1 dB ENR

The NC3000 Series calibrated coaxial AWGN sources are well suited for receiver testing, noise figure measurements, or applications that require broadband noise and fast switching times. Several models include output isolators, and voltage regulators that provide excellent stability over varying temperature and voltage ranges. The NC3000 Series includes the NC3100 units with 15 dB ENR output for noise-figure meters, and the NC3200 Series high-output noise sources with outputs between 26 and 35 dB ENR for radar and satellite communications system testing.

• Complete bias circuits
• Requires no external components
• Extremely flat output power versus frequency characteristics

The NC500 (through-hole) and NC500SM (surface mount) Series noise modules are an economical solution for built-in test requirements. They contain complete bias circuits and require no external components. Some models contain additional gain stages for high power ENR output (51 dB). The surface mount package is suitable for mounting on micro strip. The modules have extremely flat output power versus frequency characteristics that are insensitive to temperature and voltage variations.

Not all amplifiers are created equal, so how can you be certain that an amplifier will work for your needs? You deserve to be confident that the amplifiers used with your test-and measurement lab benches will meet the requirements of your specific applications, are reliable, and are equally well-supported pre-and post-sale. When it comes to application expertise, reliability and support, there is no company that does it better than Maury.

• Ideal for applications requiring high ENR and immunity to large incident RF power
• Low VSWR
• Built-in isolator

The NC3400 Series coaxial AWGN noise sources are an excellent choice for applications requiring high ENR and immunity to large incident RF power, such as ATE, radiometer, and radar systems. The calibration accuracy and flatness of the NC3400 Series noise sources are enhanced by their low VSWR. The built-in isolator provides almost constant output impedance as the noise source bias is switched on and off. The isolator also protects the noise diode from incident RF power (consult the factory for higherpower units).

An SMA female connector is standard for the RF output and a BNC female connector is standard for the bias input. Other connectors are available as options.