• 3000 VA to 15000 VA of AC Output Power 
• Combines AC/DC source and power analyzer 
• Harmonic analysis of Voltage and Current 
• Programmable Impedance 
• AC, DC and AC+DC Output Modes 
• Multiple Chassis Configurations 
• Powerful output transient generation 
• High Crest Factor Capability 
• Arbitrary waveform generation 
• IEC 61000-3-2 and IEC 61000-3-3

The SMP5xxx product family is made up of the SMP5001 through SMP5005 general purpose relays.

• Up to 96 differential channels per full rack mainframe 
• Constantly monitor input signals for fault conditions 
• Flexible configurations for detecting edges, out-of-bounds conditions and measuring pulse widths 
• Inputs can be masked, inverted, and combined to produce interrupts 
• Can be used as a time stamp module and as a digital I/O 
• Programmable debounce circuitry prevents erroneous readings 
• 10 V and 100 V input ranges 
• On-board memory stores events with IEEE 1588 timestamps 
• Synchronize reading of input states with other scanned analog channels

• Smallest size: 11.75 x 21.9 x 16 mm including controller
• Closed-loop controller embedded in micro stage
  • No separate electronics needed
  • 3.3 VDC input
  • Direct input of motion commands (I2C, SPI, UART or analog servo)
• Angular resolution ~ 0.022 deg closed loop Absolute encoding and position feedback
• Millisecond step and settle times
• Point-to-point angular positioning with closed-loop bandwidth ~100Hz
• Holds position with zero power and no jitter
• Fast integration for embedded motion in smaller instruments

The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).

• 4-Channel, 204.8 Ksa/s per channel, 24-Bit DACs 
• -115 dB spurious free dynamic range 
• Integrated 2-Channel 64-bit tachometer 
• Integrated 4-Channel DIO 
• Tight synchronization with DSA analyzers 
• Ideal for rotational measurement, and stimulus-response applications such as vibration test 
• Output modes including Sine, Burst Sine, Chirp, Burst-random and continuous random

• 8 frequency counter channels, 16 isolated digital I/O channels, 2 isolated DAC channels in a single card 
• Single frequency measurement range that works from 0.05 Hz to 1 MHz 
• Very stable TCXO base clock, 50 MHz ±1 ppm 
• 195 kΩ Input impedance with selectable coupling (AC/DC) 
• Wide differential input voltage range (±48 V) with up to 250 V working common mode voltage 
• Programmable threshold and hysteresis levels with 1 mV resolution 
• Support for quadrature encoder 
• Isolated DIO channels with up to 60 V compliance 
• Isolated and independent 16-bit DAC channels, configurable for voltage or current output

VTI Instruments Switching Modules offer SPST and SPDT configurations, supporting up to 80 channels with a switching capacity of up to 5A.

PureLine 3 Technology

• Provides an effectively noise free environment around the device under test (DUT)
• First automated probe station to achieve -190dB spectral noise*
• Up to 32x lower noise (1kHz), for improved device characterization and modelling at the 7/5/2 nm technology nodes targeted for 5G and beyond applications
• Eliminates over 97% of the environmental noise experienced in previous probe systems
• Extensive collection of FormFactor patents, electrical design knowledge, and measurement system IP

Plug In and Go

• World’s first probe station with integrated TestCell Power Management (a TestCell is a connected set of equipment, including test software, instruments, probe station, thermal system, and related measurement accessories such as cables and on-wafer probes)
• Eliminates all ground-loop induced TestCell noise
• Low field emissions
• Provides fully managed and filtered AC power to the entire system, prober and instruments

See "Specifications & Details" tab for more key features