The Direct PC bus access data acquisition system provides the required sampling rate and resolution to meet IEC 61000-4-7 measurement requirements and supports high-speed data transfers. PC-based Harmonic and Flicker test software provides real-time full-color data display updates and continuous PASS/FAIL monitoring. Automatic calculation of the maximum permissible system impedance Zsys, using the Zref and measured Flicker parameters, as required per EN/IEC 61000-3-11. Intuitive operating software provides IEC test setup, data analysis, display, with test reports in and MS Word format.

3000 VA to 15000 VA of AC Output Power  Combines AC/DC source and power analyzer  Harmonic analysis of Voltage and Current  Programmable Impedance  AC, DC and AC+DC Output Modes  Multiple Chassis Configurations  Powerful output transient generation  High Crest Factor Capability  Arbitrary waveform generation  IEC 61000-3-2 and IEC 61000-3-3

Dual Voltage ranges that support over voltage testing on 480V based systems  Instrument Setups for quickly re-establishing the known instrument state  500uS time resolution for Transients  Virtual Panels control software included  Non-Linear current waveform programming during Load mode  Phase coordination among multiple units (LKM/LKS)  Powerful set of analog controls for PHIL and Modulation tests  Trigger In & Out to permit extensive coordination with external systems  Extensive Onboard diagnostics  Digital I/O, including RS232, USB, Ethernet (GPIB optional)  Intuitive 5” color display for ease of navigation 

Dual Voltage ranges that support over-voltage testing on 480V-based systems  Separate terminal blocks for single-phase and three-phase AC power supply outputs  High Power AC and DC Source  Auto paralleling for higher power system expansion  Single and three-phase modes  Arbitrary & Harmonic Waveform Generation  Standard LXI LAN, USB, and RS-232, Optional GPIB  Step, list, and pulse voltage transients with down to 500usec resolution  Complete avionics power quality test suites  15kVA to 1MVA Power Levels  Intuitive 5” color display for ease of navigation 

2 independent, isolated 600W channels or 1 1200W channel in 1U  Voltage: 40 V to 220 V  Current: 2.72A to 20A  2μ second shunt switching recovery  Peak Power Tracking  Primary and secondary over voltage and over current  Output electronic circuit breaker  Built in fault data recorder  Power On Self-Test  Active power factor correction (PFC)  Color touch panel monitoring  Standard LAN interface  Full remote control via AMETEK SAS software or SCPI commands

Available in single and dual pack versions  Sensor simulation available to provide thermistor, strain gauges, heater loads, and cell bypass/short.  Battery behavior easily modified via spreadsheet download to simulate any battery topology including Nickel Metal Hydride, Lithium Ion, and Nickel Cadmium  Flexible Database Operation  Fully Programmable  Completely Configurable  Attention To Spacecraft Safety  Eliminates the need for test flight batteries and their associated issues

Low output capacitance  High bandwidth up to 30kHz  High resolution I-V curve simulates static and dynamic conditions  Designed for high speed Maximum Power Point Tracking (MPPT)  Can be integrated into a multi-channel system for higher power testing  Low voltage, high bandwidth version for DC Power Optimizers  EN50530 support

High Resolution IV curve simulates static and dynamic conditions Designed for high-speed Maximum Power Point Tracking (MPPT) 250HZ PP tracking speed Low output capacitance Active power factor correction (PFC) Standard LAN interface Full remote control via AMETEK m-SAS software and via SCPI commands

Integrated subsystem test  SAS, BSS, Umbilical systems  AC Input isolation  Power Validation Fixtures  Redundant OV & OI

Near Linear Power Supply  Modular  ≥0.95 PFC  Digital control loop technology  High Power Density (3.5 watts/cubic inch)  “Virtual Assets” by:  Series operation  Parallel operation  Combined operation with loads  Simple integration

High Voltage (500V) Input  Digital control loop technology  Two models: 375W & 750W  Up to 750W/500V  Parallel up to 8 automatically  Modular  High Power Density  Simple integration

High Power Density (2 VA/cubic inch)  Single or multi-phase output  Parallel operation  4.8 Crest factor  Digital control loop technology  ≥0.95 PFC  Brown-out simulation  AC 875 VA  45 to 5000 Hz  Universal AC/DC input via mainframe  User configurable  Simple integration