The EMC test system is designed for testing electromagnetic immunity of the electrical installation of vehicles and components against supply line transients. EMC - Test Equipment for the electrical installation of vehicles.

• Pulse #1 1-5/2000us, 600 V
• #1 1-5/1000us, 600 V
• Pulse #2a 1 / 50us, 600 V
• Pulse #3 5/100 ns, 800 V

• Dual Voltage ranges that support over voltage testing on 480V based systems 
• Instrument Setups for quickly re-establishing the known instrument state 
• 500uS time resolution for Transients 
• Virtual Panels control software included 
• Non-Linear current waveform programming during Load mode 
• Phase coordination among multiple units (LKM/LKS) 
• Powerful set of analog controls for PHIL and Modulation tests 
• Trigger In & Out to permit extensive coordination with external systems 
• Extensive Onboard diagnostics 
• Digital I/O, including RS232, USB, Ethernet (GPIB optional) 
• Intuitive 5” color display for ease of navigation 
• Auto-paralleling for maximum flexibility with multi-chassis configurations 
• Separate terminal blocks for single-phase and three-phase AC outputs

EMC test equipment to evaluate the resistibility of electronic devices and components when energy charged on a human body or object is discharged to the electronic devices and components. NoiseKen brand ESD simulator is available to see malfunctions or function declines of electronic equipment for appropriate evaluations compliant with IEC 61000-4-2 Ed.2 Test Standard, ISO 10605 Ed.2 Test Standard & ISO 10605 Ed.3 Test Standard. 

The ESS-S3011A features a function which enables the user to pre-program test settings to minimize setup errors as well as having the unit be incorporated into a remote or autonomous testing setup. Another feature that sets apart NoiseKen ESD guns to that of competitors is the discharging gun separation design which helps achieve the lightweight. 

For conventional ESD guns, that have generators that are inseparable from the gun, you may experience having to replace the whole unit even only when certain parts of the unit are broken. However, with the NoiseKen’s separation design, replacement parts can be minimized to lower the running cost.

• Compliant with IEC 61000-4-5 Ed.3 standard：ECE R10 is regulated at Ed.2, possible to switch to Ed.2
• AC500V/200A DC600V/200A built-in coupling decoupling network.
• Built-in EV relay welding protection diode in DC line. You can evaluate the lightning surge resistance when charging EV / PHV vehicles, which is required by ECE R10-04 / 05. (EV Fast Charging applicable)
• Maximum output voltage 15kV: In the reliability evaluation test of the lightning surge test, the evaluation including the destructive test can be performed.
• Adopt a large LCD screen operation panel: A large LCD panel screen has been adopted for the operation unit to improve visibility and operability.
• Employs MPU control that simplifies continuous testing: Surge output / waveform switching / polarity switching / sequence operation can be performed automatically.
• Equipped with manual and program modes. Manual mode for standard tests and single condition tests, and Program mode for continuous tests under different conditions. You can easily set test conditions according to your application.
• Excellent safety functions including interlock
• Equipped with waveform check terminal as standard
• You can check the output waveform with your oscilloscope and BNC cable.
• Isolation transformer required to protect the power supply for EUT is available. (option)
• Possible to switch the constant of the decoupling circuit in order to prevent resonance with the power supply.
• Possible to switch to a circuit not including 18uF in the surge output of IEC61000-4-5 Edition 2.0 2005 version).

* This product is a custom product. Please contact us for details.

Customization up to DC1000V is available.

Our 2 Series cable assembly showcases excellent phase stability against bending, developed with microwave/mmWave measurement environments in mind.

Its flexibility means low repulsion, reducing the load on the measured object

Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.

• Excellent cutting results through precision cutting
• Improved sample quality through an exact and reproducible sample thickness
• Very durable blade, 7 times blade rotation possible (360°)
• Exact adjustment of the rotating speed
• The influence of the operator is minimized by the predefined blade feed
• Fine, manual dosing of the progressive feed
• Easy exchange of the wire grips possible, with standard tooling
• Intelligent control electronics ensure an intuitive and safe operation

• V4A, AISI 316L Stainless Steel (apart from hygienic standard mounts).
• IP69k ingress protection rating for high pressure cleaning up to 100 bar, dual seal system for additional safety.
• Most stringent hygienic design for use in direct food contact and dripping areas, EHEDG Certification in progress.
• All seal materials, protective tubes and acrylic windows with FDA approval.
• All enclosure materials tested according to ECOLAB standards with aggressive cleaning agents (Topactive 200/ 500/ OCTO, P3 Topax 66/ 990).
• Flexible vibration proof camera mount inside the enclosure with very good heat dissipation.
• Flexible mounting of camera enclosure.
• Different rear and side exit versions and mounting accessories available.

• Available in single and dual pack versions 
• Sensor simulation available to provide thermistor, strain gauges, heater loads, and cell bypass/short. 
• Battery behavior easily modified via spreadsheet download to simulate any battery topology including Nickel Metal Hydride, Lithium Ion, and Nickel Cadmium 
• Flexible Database Operation 
• Fully Programmable 
• Completely Configurable 
• Attention To Spacecraft Safety 
• Eliminates the need for test flight batteries and their associated issues