• Complete bias circuits
• Requires no external components
• Extremely flat output power versus frequency characteristics

The NC500 (through-hole) and NC500SM (surface mount) Series noise modules are an economical solution for built-in test requirements. They contain complete bias circuits and require no external components. Some models contain additional gain stages for high power ENR output (51 dB). The surface mount package is suitable for mounting on micro strip. The modules have extremely flat output power versus frequency characteristics that are insensitive to temperature and voltage variations.

• Capture/display/analyze peak and average power
• Frequency range from 4 kHz to 40 GHz
  • Industry-leading video bandwidth (195 MHz) and rise time (3 ns)
  • Industry-leading 100,000 measurements per second
  • Industry-leading 100 ps time resolution
• Synchronous multi-channel measurements (up to 4 channels)
• Sensors can be used as standalone instruments

The EH118 EMC Horn combines stable gain performance and low VSWR with wide band frequency operation. The horn is single linearly polarized with excellent cross-polar discrimination. The unique horn design suppresses any possible excitation of higher order modes in the aperture and maintains a well-defined smooth radiation pattern in the direction of the boresight axis throughout the operational bandwidth.

High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.

• 1-18GHz Frequency Range
• Compensation long cable loss for EMI Measurement
• Improve system noise floor flatness
• High EMI performance
• High linearity LNA for EMI measurement
• High dynamic range
• Unconditionally Stable
• State-of-the-Art Technology

• 2-port VNA with frequency options from 1 MHz to 8 GHz / 20 GHz / 43.5 GHz (options for 20, 50, and 100 meters)
• Extend remote ports 100 meters apart with PhaseLync synchronization
• Small and lightweight ports enable direct connection to DUT eliminating long cable runs
• Guaranteed performance to 43.5 GHz with Extended-K™ ports
• PC control takes advantage of external computer processing power and functionality
• No on-board data storage makes use in secure applications more convenient
• Common ShockLine control software delivers powerful debug and test capabilities
• PhaseLync control module MN25132A

• High performance GPS disciplined Time/Frequency standard 
• Ethernet Interface for management and control 
• Network Time Protocol (NTP) 
• Multiple 1PPS outputs with individual delay compensation 
• Multiple Low Phase Noise 10MHz outputs with software programmable level 
• Time Code outputs including Have Quick, IRIG A, IRIG B, IRIG E, IRIG G 
• Sync to GPS or to Have Quick/1PPS per ICD-GPS-060 
• Choice of internal disciplined OCXO or Rubidium Oscillator

• Frequency range of 9 kHz to 3.6 GHz/6 GHz/26.5 GHz/44.5 GHz; 44.5 GHz max. built-in preamp option
• Best close-in phase noise performance in middle range signal analyzer/spectrum analyzer: 
  • –123 dBc/Hz (at 1 GHz center frequency, 10 kHz offset frequency with all frequency models) 
  • –138 dBc/Hz (at 1 GHz center frequency, 10 kHz offset frequency with 3.6 GHz and 6 GHz models, meas.) 
  • –140 dBc/Hz (at 150 MHz center frequency, 10 kHz offset frequency with 3.6 GHz and 6 GHz models, meas.)
• 31.25 MHz analysis bandwidth (standard); 125 MHz max. (option)
• All-in-one solution with built-in signal generator option supports TRx tests (with 3.6 GHz and 6 GHz models)
• Measurement applications (options): Phase Noise Measurement, Noise Figure Measurement, Vector and Analog Modulation Analysis, BER Measurement, Pulse Radar Measurement Function

• Dual-channel and differential voltage measurements
• 1% accuracy at full scale
• True RMS response below 30 mV
• Optional low-frequency probe for measurements from 10 Hz to 100 MHz
• DC recorder output
• IEEE-488 interface standard, RS-232

The 9240 series is the latest addition to the popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range. It is simple to use on the bench, and comprehensive enough to integrate into an ATE system. Boonton’s proven voltage probes directly measure from 200 μV to 10 V with usable indication as low as 50 μV and have true RMS response below 30 mV.