NEO NXB - 12030 Voltage / Current Breakout Test Box
-
On-Off power switch
-
30 A Circuit Breaker
-
Inlet - NEMA L5-30
-
Outlets – NEMA L5-30R
Test Tap:
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
Single output for passthrough to test rack. Tester pigtail interface simplifies connecting to a variety of voltage/current measuring systems.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
208 | 30A | L6-30 - Cord | L6-30R | Pigtail | Yes |
Application
More Product Information
-
NEO 941 parts are AS5836 compatible (Clam Shell Clamps not Included)
-
NEO 942 parts are AS1653 compatible (Clam Shell Clamps not Included)
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
24-bit, delta-sigma ADC, simultaneous sampling
-
Programmable Sample Rate up to 128kSPS
-
Full, Half & Quarter Bridge with 120Ω, 350Ω & 1kΩ bridge completion
-
Voltage Excitation: 0.5V to 10V
-
Current Excitation: 0.46mA
-
2-Wire & 4-Wire Ohms/RTD
-
Bridge Zero Balancing
-
Built-In-Self-Test (BIST)
-
Strain Lead Wire Calibration
-
Shunt Calibration: 50kΩ, 100kΩ & External provided by User
-
TEDS Support
-
LXI Ethernet Interface
-
IEEE-1588 Synchronization
-
Power over Ethernet (PoE) or 10–50 V DC input
-
Built-in Parallel Data Streaming
-
Full-featured Embedded Web Interface
-
Compact 1U Half-rack Form Factor
-
3KVA, 3KW Double Conversion On Line Isolated 115VAC Input UPS, and simultaneous 120 and 240VAC 60Hz Output, Power Factor Correction, Extended Internal Batteries, SNMP Communications for Military Applications
-
Verify quality of optical fiber cable assemblies, connectors and short-run networks
-
Troubleshoot and distinguish between macro-bends, splices, connectors and breaks
-
Locate insertion loss points – save hours of troubleshooting time
-
Verify return loss of multiple points in a fiber assembly or harness simultaneously
-
Verify and maintain aircraft and shipboard networks
-
Customize GUI for automated pass/fail verification of your fiber assembly using software development kit
The system detects position of the magnetic field sensor on the basis of the image on the camera first of all and then, recognizes strength of the signal that is measured by the sensor upon frequency analysis of the signal almost simultaneously. Finally, visualization of the strength level in composition with the real image of the measured object can be realized on screen of PC in form of heat map in colors.
-
High responsiveness following to the image can be realized because of the image recognition setting according to colors on the sensor part.
-
Composite strength distribution of the actual image taken by the camera and the measured data can be visualized.
-
Single measurement, all-parameter analysis
-
Full characterization of components in less than 3 seconds
-
Complete polarization response
-
With single scan, simultaneously measure loss, polarization, dispersion, phase and time domain response
-
Available for C and L band, or O band
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.
Test & Measurement
Download Line Card
Document