• Measuring device for large extrusion tools up to 35 mm (1.37“) hole diameter 
• Automated measurement process 
• Focus indicator allows you to easily adjust the focus 
• Homogeneous transmitted light illumination - made by iiM GmbH - for the ideal presentation of the area to measured 
• The influence of the user is reduced to a minimum 
• Robust, ergonomic design 
• Ideal addition to the 2-camera system VCPEx+

• 2 in 1: device contains the Hot Set Test as well as the Heat Pressure Test
• Robust and compact set including the device and an equipment case
• Possibility to attach a thermometer directly near the sample
• Measurement according to the cable standards IEC 60811 -507 (Hot Set Test) and IEC 60811 -508 (Heat Pressure Test) regarding sample attachment and weight attachment
• Precise choice of weights due to practical containers
• Simultaneous measurement of up to 3 cable or tube samples

EMI Measurements:

• FFT-based dual-channel receiver
• According to CISPR16-1-1
• Peak, Quasi-Peak, and Average Detectors
• Resolution Bandwidth Filters of 200 Hz, 9 kHz, and 120 kHz (CISPR), and 1 kHz and 10 kHz (MIL)
• The fastest receiver in the market: Line and Neutral measurements with the 3 detectors simultaneously (6 simultaneous measurements)

NEO X01 3000 PSI Adapters

• Up to 96 differential channels per full rack mainframe
• Constantly monitor input signals for fault conditions
• Flexible configurations for detecting edges, out-of-bounds conditions and measuring pulse widths
• Inputs can be masked, inverted, and combined to produce interrupts
• Can be used as a time stamp module and as a digital I/O
• Programmable debounce circuitry prevents erroneous readings
• 10 V and 100 V input ranges
• On-board memory stores events with IEEE 1588 timestamps
• Synchronize reading of input states with other scanned analog channels

• 600 MHz of instantaneous bandwidth per channel
• Timing synchronization up to 16 channels
• Link Emulation including:
  • Phase continuous delay, Doppler, and attenuation changes
  • AWGN and Eb/No
  • 12 tap (path) multipath fading with Rayleigh, Rician & CW. Angle of Arrival (AOA), k-factor, and correlation controls
  • RF frequency agile up/down converters
• Payload Emulation including:
  • IMUX/OMUX amplitude and group delay distortion
  • Amplifier Compression (AM/AM and AM/PM)
  • Phase Noise
• Static and dynamic link emulation
• Ephemeris data generation using SATGEN
• Remote instrument control through ACEClient application

• Red laser for long lines and good visibility
• Optical output power up to 40mW/635 nm
• Integrated power supply with high immunity to interference
• Dimensions: Ø 40mm x 200m
• wide range input, 90-265VAC

The ZR is a red positioning laser with an asymmetric optic that projects especially long and homogeneous lines for precise alignment. With an optical output of up to 40 mW at 635 nm, it provides excellent visibility even across large working areas. An integrated heavy-duty power supply with a wide input range (90–265 VAC) ensures strong interference resistance and reliable operation under demanding industrial conditions. Compact dimensions of Ø 40 mm x 200 mm make it easy to integrate into machines and systems. Typical applications include textile tables and circular saws, where long and uniform line projection is critical for accuracy.

The VTI Instruments 16-Channel isolated high voltage measurement instrument

• 24-bit SAR ADC per Channel
• 128k samples/second/channel sample rate
• 1000V channel-channel isolation
• 500V channel-ground isolation
• Input voltage ranges peak: ±420V/±10V/±1V
• Data logger acquisition mode
• 3-Pin screw terminal input connector
• LXI ethernet interface
• IEEE-1588 synchronization
• Power over Ethernet (PoE+) or 12– 50 V DC input
• Simultaneous data streaming
• 8-bit bank isolated digital I/O
• Full-featured embedded web interface
• Compact 1U half-rack form factor