Teledyne LeCroy - T3SA Series 2.1 GHz and 3.2 GHz Spectrum Analyzers
- All Digital IF technology
- 10.1” WVGA (1024 x 600) Display
- Frequency range from 9 KHz up to 3.2 GHz
- -161 dBm/Hz Displayed Average Noise Level (Typ)
- -98 dBc/Hz @ 10 khz Offset Phase Noise (Typ)
- Total Amplitude Accuracy < 0.7 dB
- 1 Hz Minimum Resolution Bandwidth (RBW)
- Comes with Preamplifier
Teledyne Test Tools new T3SA3000 family of Spectrum Analyzers offers a frequency range of 9 KHz to either 2.1/3.2 GHz alongside many impressive features. With their light weight, small form factor, and user friendly interface, these Spectrum Analyzers take powerful and reliable automatic measurements that are presented on a large, bright, easy to read touch screen display. Typical uses for the T3SA3000 series are research and development, education, production, maintenance, and pre-compliance testing.
Easy to operate, Supports Four Independent Traces and Cursors
The T3SA3000 series has four selectable color-coded traces which can be used for different functions such as Max Hold, Min Hold, Clear-Write, Math, Average, etc.
More Product Information

Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.

- Up to 20 GHz bandwidth and 80 GS/s sample rate
- The most advanced oscilloscope user interface
- The industry’s only true hardware 14.1 Gb/s serial trigger
- Low Jitter Measurement Floor and exceptional timebase stability
- Comprehensive set of serial data analysis, debug, validation and compliance tools
- Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility
- Integrated standard and custom measurements and math functions for unrivaled analysis capability
- Multi-lane serial data eye, jitter and crosstalk analysis
- Real-time de-embedding, emulation, and equalization

- Image acquisition from Camera Link Base camera
- Supports Camera Link® operations up to 85MHz
- Supports 32/64-bit Windows platforms
- Quarter-length PCI Express x1 Board
- Power Over Camera Link® (PoCL) Compliant
- Offers external acquisition control signals on single PCIe x1 slotROHS compliant

- Global shutter and rolling shutter CMOS sensors available
- USB3 Vision
- High sensitivity with both front and back illuminated sensors (BSI)
- Side mounted USB connectors for ease of use in OEM solutions
- High sensitivity with pixel sizes from 2 µm to 3.45 µm
- Windows operating system and Linux SDKs (for embedded vision systems)
- 3-Year Warranty

- Ideal probe for up to 48 V power conversion
- 250, 500 MHz and 1 GHz bandwidth
- 80 V dynamic range
- 60 V common mode
- Highest accuracy
- 0.5% gain accuracy
- Precision gain calibration
- Best LF flatness (0.1 dB)
- Lowest noise and highest rejection
- Wide variety of tips
- High performance solder-in
- Browser
- Single pins and header
- Mini and micro grabbers
- Socketed connections
- High temp solder-in
- Y-banana adaptor
- ProBus active probe interface
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.

- Latest Global and Rolling Shutters sensors from Sony® - from 2 to 12 MP
- USB3 Vision interface
- Compact fully-enclosed design with features needed by modern vision systems
- Provide advanced vision performance while using less power, less space, and fitting increasingly tight industry budgets

- Four operating modes: – CC, CV, CR, CP.
- Static, Dynamic and Sequence mode support.
- Built in Application Functions - Short Circuit Test, Battery Test Mode, CR-LED Mode, OCP and OPP Test.
- Provides a load of up to 300 Watts.
- Programmable and analog external control.

Teledyne LeCroy
Teledyne LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types. Since our founding in 1964, we have focused on creating products that improve productivity by helping engineers resolve design issues faster and more effectively.
Oscilloscopes are tools used by designers and engineers to measure and analyze complex electronic signals in order to develop high-performance systems and to validate electronic designs in order to improve time to market. Protocol analyzers are tools used by designers and engineers to generate and monitor traffic over high speed serial data interfaces, including DDR, PCI Express, Fibre Channel, Serial ATA, SAS, USB and others. Both products are critical in the development of a wide variety of demanding design applications.
We utilize both of these important product areas in combination to tackle the most demanding serial data test applications, offering tailored solutions to help our customers perfect their chips, interfaces, subsystems and products which utilize these important communications standards. With the explosion in the use of serial data communications technologies in semiconductors, between devices on circuit boards and between computers and peripherals, we are aimed at a growing and important market.
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
Headquartered in Chestnut Ridge, New York, LeCroy has sales, service and development subsidiaries in the US and throughout Europe and Asia. LeCroy products are employed across a wide variety of industries, including semiconductor, computer, consumer electronics, military/aerospace, automotive/industrial, and telecommunications.
Contact Details
Headquarters Teledyne LeCroy
700 Chestnut Ridge Road, Chestnut Ridge, NY 10977-6499, USA
Phone: 800-553-2769 or 845-425-2000
Phone Support: 1-800-553-2769
Fax Sales: 845-578-5985
Email Sales: contact.corp@teledynelecroy.com
Email Support: support@teledynelecroy.com (Oscilloscopes, Waveform Generators, Signal Integrity)
Test & Measurement
