• Expandable frequency range from 18 to 325 GHz
• 2 to 3 times better accuracy
• Automatic Nitrogen purge eliminates helium equipment
• Primary calibration standard
• Radiometer reference source
• SATCOM earth station conformance verifications

• Test plan development
• Order administration
• Archiving of obtained test results
• Creation of result lists according to the test plans
• Correct and structured filing of test results
• Exceedance of tolerance limits are immediately reported and saved
• Possibility to connect with external measuring devices (please inquire type)
• Connection with a SQL or MS Access© database possible

• For camera operation in up to 70°C ambient temperature without sun radiation
• Up to 50°C with 350W/m² sun radiation
• Permanent temperature control
• Good UV and ageing resistanc
• IP65 (camera enclosure)/IP54 (fan)
• 3" or 4" window for large lensesOther window materials avialable
• All Orca extensions and front lids incl. dome window usable
• With Orca extension with Meganova usable
• Only DC voltage required, easy handling
• Fully automatic operation, heating or cooling (depending on version)

• Single or dual-channel display
• Agilent HP 437 & Agilent HP 438, and Boonton 4220A & 4230A emulation
• Automatically loads sensor data
• Simple software control via SCPI language
• IEEE-488 and RS-232 interfaces standard

The 4240 series of CW RF power meters provides the high speed measurement capability needed in a production environment, as well as the simplicity of operation required for bench top use. It provides very accurate measurements from -70 dBm to +44 dBm (sensor dependent) and has a rapid display update rate for tuning applications. The easy to read LCD displays both channels simultaneously with numeric and bar graph information.

• Wide Input Bandwidth 
• Input Isolation 
• Automatic & Manual Changeover 
• Transformer Coupled Outputs 
• Twenty four Outputs 
• Front Panel Status Indicators 
• Fault Discrete Inputs 
• Compact 1U, 19” rack mount

• Preparation of cable samples for further processing
• Applicable for cable types with solid core cross-sections
• E.g. Sample preparation for cutting with ORC family

• 2000 Vrms input
• 6000 Vpeak transients
• Up to 500 MHz bandwidth
• Ideal for Surge/EFT testing

High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.

• Compliant with IEC 61000-4-5 Ed.3 standard：ECE R10 is regulated at Ed.2, possible to switch to Ed.2
• AC500V/200A DC600V/200A built-in coupling decoupling network.
• Built-in EV relay welding protection diode in DC line. You can evaluate the lightning surge resistance when charging EV / PHV vehicles, which is required by ECE R10-04 / 05. (EV Fast Charging applicable)
• Maximum output voltage 15kV: In the reliability evaluation test of the lightning surge test, the evaluation including the destructive test can be performed.
• Adopt a large LCD screen operation panel: A large LCD panel screen has been adopted for the operation unit to improve visibility and operability.
• Employs MPU control that simplifies continuous testing: Surge output / waveform switching / polarity switching / sequence operation can be performed automatically.
• Equipped with manual and program modes. Manual mode for standard tests and single condition tests, and Program mode for continuous tests under different conditions. You can easily set test conditions according to your application.
• Excellent safety functions including interlock
• Equipped with waveform check terminal as standard
• You can check the output waveform with your oscilloscope and BNC cable.
• Isolation transformer required to protect the power supply for EUT is available. (option)
• Possible to switch the constant of the decoupling circuit in order to prevent resonance with the power supply.
• Possible to switch to a circuit not including 18uF in the surge output of IEC61000-4-5 Edition 2.0 2005 version).

* This product is a custom product. Please contact us for details.

Customization up to DC1000V is available.

• Measuring device for large extrusion tools up to 35 mm (1.37“) hole diameter 
• Automated measurement process 
• Focus indicator allows you to easily adjust the focus 
• Homogeneous transmitted light illumination - made by iiM GmbH - for the ideal presentation of the area to measured 
• The influence of the user is reduced to a minimum 
• Robust, ergonomic design 
• Ideal addition to the 2-camera system VCPEx+