Absolute EMC - Low Frequency Immunity
See "Specifications & Details" tab for more information.
|
The Wood Test Table is a simple, inexpensive solution for your EMC testing. The table is built to be ship flattened to reduce shipping costs and easily assembled on site quickly. The picture is shown with a ground plane. |
|
Absolute EMC offers an assortment of injection test kits for the use of conducted immunity. The kits can be used with many available conducted immunity systems, including the Schlöder CDG 7000, to make selection and setup easy. All calibration fixtures, injection clamps, attenuators, and termination resistors necessary for meeting the requirements of conducted immunity systems. All all-in-one systems are covered. |
|
Low-profile 12'×10' floor plane with matching vertical wall (up to 12'×10') in galvanized steel. |
|
Staggered two-layer floor design: wide metal-to-metal overlap, ultra-low impedance, almost zero step height. |
|
Fast install (1–2 days) with full bonding/continuity verification to the building ground or a shielded room. |
|
Engineered to meet IEC 61000, CISPR, and MIL-STD-461 ground-plane requirements. |
|
Custom sizes/materials (steel, aluminum, copper), edge ramps, LISN pads, and cable trenches available. |
|
Delivers repeatable EMC/ESD results by minimizing loop impedance and stray coupling paths. |
More Product Information
- Tiny “all-in-one” solution: no external control board needed
- Superior image quality: sub-micron lens movement with very low tilt. Now with higher dynamic stability
- Low voltage & power: 3.3 VDC input, zero power position hold
- Simple system integration: accepts high-level motion commands over standard serial interface (I2C or SPI)
- Flexible, production-ready system: compatible with M8 to M16 lenses and with typical image formats from 1/3” to 1/1.8”
- Lowest cost, fastest time to market: Fully-engineered “plug and play” solution
The VectorStar ME7838 Series broadband VNA offers the widest available single frequency sweep from 70 kHz to 110, (ME7838AX to 125), (ME7838EX to 125), to 145 GHz, and to 220 GHz with mmWave bands to 1.1 THz.
- The ME7838AX or ME7838EX version can easily be upgraded to 145 GHz and to 220 GHz
- All versions may be configured to include banded millimeter-wave modules up to 1.1 THz
- Industry-best calibration and measurement stability: 0.1 dB vs 0.6 dB over 24 hrs.
- All versions support the 3744x-Rx receiver for noise figure measurements, including the ability to characterize differential noise figure, to 125 GHz
- Compact, lightweight mmWave modules (0.6 lb vs 7+ lbs and 1/50 the volume) offer low cost installation on smaller probe stations.
The MDR system is your key to data collection in challenging, real-world airborne flight test scenarios. Its modular design allows it to seamlessly adapt to the full spectrum of test requirements, whether it’s a lightweight task or an extensive mission with diverse signals, environmental challenges, and lengthy recording periods.
A comprehensive range of signal interface modules, custom-tailored for various data sources and bus types, ensures that it’s ready to meet today’s demands and future requirements.
-
Versatile temperature range for extreme environments
-
IEEE 1588 PTP
-
Power over Ethernet
-
P-Iris and DC-Iris lens control
-
Monochrome (GT2050) and color (GT2050C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Defect pixel masking feature with the Defect Mask Loader tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
High SNR mode (up to 24 dB better signal-to-noise ratio)
-
Low-noise binning mode
-
Shading correction
-
Defect pixel correction
-
Area of interest (AOI), separate AOI for auto features
-
Binning
-
Decimation
-
Auto gain (manual gain control: 0 to 24.4 dB)
-
Auto exposure (31 µs to 67 s)
-
Auto white balance
-
Look-up table (LUT)
-
Hue, saturation
-
Color correction
-
Local color anti-aliasing
-
Reverse X/Y
-
Deferred image transport
-
Trigger programmable, level, single, bulk, programmable delay
-
Sequence mode (changes the camera settings on the fly)
-
SIS (secure image signature, time stamp for trigger, frame count etc.)
-
Storable user sets
Scope of delivery
-
Camera and IEEE 1394b cable (other configurations on request)
- 1 - 6 GHz, 40dB Gain, 2.5dB N.F.
- Compensation long cable loss for EMI Measurement
- Improve system noise floor flatness
- High EMI performance
- High linearity LNA for EMI measurement
- High dynamic range
- Unconditionally Stable
- State-of-the-Art Technology
The SM7000 Series microwave switching modules are members of the VXI Technology SMIPII™ family. They offer a modular design allowing custom switching configurations to be easily assembled and modified in the field.
The SM7000 is a single-wide, C-size VXI module, which can support up to six different microwave switches including: a dual SPDT; SP3T through SP6T; transfer switches and passthrough adapters that allow the module to control up to eight externally mounted relays each.
-
Camera Link InGaAs SWIR camera
-
VGA resolution
-
Large pixel with high dynamic
-
Strong sensor cooling
-
No condensation
-
Very strong sensor cooling for low-noise imaging with long exposure times
-
Camera Link interface with GenCP support
-
Comprehensive I/O control options
-
Automated on-board image correction
-
Extended operating temperature range
- All-in-one smart module: no separate electronics
- Runs directly from USB adapter
- USB, I2C or SPI interface
- Small size: less than 29 x 20 x 10 mm
- High resolution: 0.5 μm
- Absolute encoding: no homing
- Long stroke: 6 mm
- Low power use: 3.3 V DC input, < 0.75 W when moving
- High repeatability and low runout
Absolute EMC
Absolute EMC LLC is a premier North American provider of electromagnetic compatibility (EMC) expertise and test equipment. They deliver end to end consulting—covering IEC, MIL STD, CISPR, and automotive standards—hands on training for all EMC and RF test instruments, and turnkey test system design and integration. Leveraging decades of experience with every major manufacturer and the latest technologies, they also offer strategic guidance on equipment selection, market trends, and procurement to help you maximize the performance and ROI of your EMC investments.
Contact Details
Absolute EMC LLC
8240 Rugby Road, Manassas Park VA 20111, USA
Phone: 703-774-7505
Email: info@absolute-emc.com
Test & Measurement
Download Line Card
