• 2 in 1: device contains the Hot Set Test as well as the Heat Pressure Test
• Robust and compact set including the device and an equipment case
• Possibility to attach a thermometer directly near the sample
• Measurement according to the cable standards IEC 60811 -507 (Hot Set Test) and IEC 60811 -508 (Heat Pressure Test) regarding sample attachment and weight attachment
• Precise choice of weights due to practical containers
• Simultaneous measurement of up to 3 cable or tube samples

• Up to 96 differential channels per full rack mainframe 
• Constantly monitor input signals for fault conditions 
• Flexible configurations for detecting edges, out-of-bounds conditions and measuring pulse widths 
• Inputs can be masked, inverted, and combined to produce interrupts 
• Can be used as a time stamp module and as a digital I/O 
• Programmable debounce circuitry prevents erroneous readings 
• 10 V and 100 V input ranges 
• On-board memory stores events with IEEE 1588 timestamps 
• Synchronize reading of input states with other scanned analog channels

• On-Off power switch
• 20 A Circuit Breaker
• Inlet - NEMA L6-20
• Outlets – NEMA L6-20R

• 3ft.
• (2) fork terminals (current)
• (1) fork terminals (ground)
• (2) Shielded Banana (voltage)

• Robust and compact design, easy to handle
• Fast, reliable and highly accurate measuring process
• Integrated hardware and software, touch monitor for intuitive operationReliable, high-precision clamping of the test specimen (including conical tools / conical wire guides)
• The highly precise alignment of camera and test object chuck both enable a highly accurate measurement
• No extraneous light influences thanks to measuring behind closed sliding door

NEO X05 5080 PSI Adapters

• 600 MHz of instantaneous bandwidth per channel
• Timing synchronization up to 16 channels
• Link Emulation including:
  • Phase continuous delay, Doppler, and attenuation changes
  • AWGN and Eb/No
  • 12 tap (path) multipath fading with Rayleigh, Rician & CW. Angle of Arrival (AOA), k-factor, and correlation controls
  • RF frequency agile up/down converters
• Payload Emulation including:
  • IMUX/OMUX amplitude and group delay distortion
  • Amplifier Compression (AM/AM and AM/PM)
  • Phase Noise
• Static and dynamic link emulation
• Ephemeris data generation using SATGEN
• Remote instrument control through ACEClient application

• Single-mode fiber with FC/PC connector
• Unique line uniformity and μ-optics for thin lines ( <15 μm [1/e²] )
• Red, green and blue wavelengths
• Optical output power up to 35 mW
• < 15 μm bei FWHM
• M2 < 1.05
• Analog and simultaneous TTL modulation up to 200 kHz
• Fail-safe for critical applications (e. g. medical)
• OEM-version without housing and TEC (PCB-version)

The VTI Instruments 16-Channel bridge and strain gauge measurement instrument

• 24-bit, delta-sigma ADC, simultaneous sampling
• Programmable Sample Rate up to 128kSPS
• Full, Half & Quarter Bridge with 120Ω, 350Ω & 1kΩ bridge completion
• Voltage Excitation: 0.5V to 10V
• Current Excitation: 0.46mA
• 2-Wire & 4-Wire Ohms/RTD
• Bridge Zero Balancing
• Built-In-Self-Test (BIST)
• Strain Lead Wire Calibration
• Shunt Calibration: 50kΩ, 100kΩ & External provided by User
• TEDS Support
• LXI Ethernet Interface
• IEEE-1588 Synchronization
• Power over Ethernet (PoE) or 10–50 V DC input
• Built-in Parallel Data Streaming
• Full-featured Embedded Web Interface
• Compact 1U Half-rack Form Factor

NEO X01 3000 PSI Adapters