The broadband horn antenna BBHA 9120 J is a linear polarized high gain antenna. The gain increases from 11 dBi at 1GHz up to more than 20 dBi at higher frequencies. 800 MHz to 6.2 GHz N (optional 7/16) Gain 11 dBi - 20 dBi

Low Noise Amplifier (preamp) 9 kHz - 8 GHz Typical gain: 27 dB Noise Figure: 2.7 dB

Common-Mode Absorbing Clamp (10) 30 - 200 (1000)MHz Suppress unwanted common mode currents Cable bundles maximum diameter of 26 mm acc. CISPR 16-1-4

High Current 4 path LISN (3-Phase & Single-Phase) Line Impedance Stabilization Network Connector: CEE plug (IEC 60309) & CEE 7/4 9 kHz to 30 MHz 250/400 VAC, 400 VDC, 32 A (16A for CEE 7/4) (50 µH+5 Ω) || 50 Ω CISPR 16-1-2

The VULP 9118 E is a polarized log-periodic antenna (50) 75 - 1500 MHz 1 kW (w/ 7-16 High power 5.4 kW) Type N (female) or 7-16 DIN (f)

The Precision Omnidirectional Dipoles POD 16 and POD 618 are fully compliant to CISPR 16-1-4 for site validation above 1 GHz. The POD 16 and POD 618 are precision broadband dipole antennas with conically shaped radiation elements covered by an RF-transparent radome. This rugged construction enables an excellent dipole-like radiation pattern up to 18 GHz.

Precise programming of voltage and current slew rate for sensitive loads.  Industrial field bus interfaces (Modbus-TCP, Modbus-RTU, Ethernet) enable real-time digital control.  Built-in power quality monitoring detects and saves input voltage anomalies which can be saved for later diagnostic analysis.  Programmable analog interface scaling facilitates integrating the ASD FLX with existing systems easily.  Built-in energy meter calculates the delivered energy throughout a process or period.  Optional real-time clock enables accurate timestamping of events.

Three independent, isolated DC output power supply 600W channels  Total DC power density up to 1800W in a 1U chassis  5 autoranging output channel options  Intuitive color touch panel control  Multi-language display for global operation  Multi-channel programmable sequencing, ramps, and delays  Active power factor correction (PFC)  Standard LXI LAN, USB, and RS232 interfaces  Optional GPIB interface  Full remote control via Virtual Panels™

Three independent, isolated 1700W DC outputs, 5100W total  1U rack-mount chassis  9 output options  Multi-language, intuitive, color touch panel control  Global 3-Phase AC Input options for system phase balancing  Active power factor correction (PFC)  Multi-channel programmable sequencing, ramps, and delays  Full remote control via Virtual Panels™ GUI  Standard LXI Ethernet, USB, and RS232 control interfaces  Optional GPIB control interface or isolated analog programming

High power density DC power supply in a 1U chassis (up to 5 kW) or a 2U chassis (up to 10 kW)  Intuitive touch panel control  Available in either Fixed or Autoranging output  Multi-language display for global operation  Auto paralleling for higher power  Full remote control via Virtual Panels™

Energy absorber with a rating of 400VDC at ±150A  Provides up to 400V at 150A for 60kW of output power Energy Absorber Load chassis creates a total resistance of approximately 1.5 Ohms at 30kW continuous and 60kW peak

High power density / low ripple and noise  High programming resolution with Ethernet interface  Constant voltage and current mode  Remote sensing  Isolated analog control and monitoring (optional)